To break down the eutectic carbide network of A-cast structure with grain size 4-5 grade, tensile strain of 60% is needed.

In order to detect the carbide network in high carbon hypereutectoid steel wire rods accurately, two kinds of detection method of the carbide network are compared.

为了准确地检验高碳过共析钢盘条中的网状渗碳体，分别对选用硝酸酒精溶液侵蚀和碱性苦味酸钠水溶液热侵蚀两种显示方法进行了比较。

While forging the high-carbon chromium bearing steel by the finish forge press, there still remains the issues that the carbide network can not be crushed with the low qualification rate.

精锻机锻造高碳铬轴承钢时存在网状碳化物不易破碎、锻件合格率低的问题。

Fundamental Study on Iron Carbide Formation by Two-Step Method

二步法制备碳化铁的基础研究

Phase Analysis and Production Mechanism of Iron Carbide

Fe3C生成机理及物相分析

Iron carbide-a new iron product for direct reduction

碳化铁&新型的直接还原铁产品

The influence of temperature on iron carbide made with the gas from coal

温度对煤造气制备碳化铁的影响

The technique of centrifugal casting was used. Study on Freeze-Casting of Aqueous Silicon Carbide/ Carbon Black Slurry

采用离心浇注法成型。水基碳化硅/炭黑料浆冷冻浇注成型工艺研究

Coating silicon carbide on carbon fibres by PVD

用物理溅射法在碳纤维表面涂覆SiC

Silicon Carbide-Carbon Composite Material& Siliconized Graphite

碳化硅-碳复合材料&硅化石墨

Functional Silicon Carbide-Carbon Fiber

碳化硅-碳功能纤维

Comparison between calculated and experimental adsorption data showed that the prediction was satisfactory, and the average deviations between the calculated and experimental values for Shanghai made Carbon and Union Carbide Carbon were 1.8% and 3.1% respectively.

吸附量预计值和实验值的比较，表明预计是令人满意的。对于国产活性炭和美国联合炭化合物公司活性炭，其预计值和实验值的平均相对误差分别为1.8%和3.1%。

The results showed that methane exhibited rather high decomposition activity and carbide carbon and graphitic carbon were detected.

结果表明，甲烷具有相当高的裂解积炭活性，裂解后生成炭化物（carbide炭）和石墨炭两种不同活性的炭种；

Simulation analysis of detection of crack location in a steel beam by using wavelet packet-neural networks Calcium carbide steel drum for the home market

模型钢梁裂缝检测的小波包网络仿真GB/T15956-1995内销电石包装钢桶

Quality Control of CVD Coating Carbide Tool in High-accuracy Cutting

高精切削用CVD涂层硬质合金刀具的质量控制

Several motion manners of the carbide tool surface grinder were introduced.

作者首先介绍了硬质合金刀片端平面研磨机的几种运动方式；

Experimental Study on Coated Carbide Tool Turning Austenitic Stainless Steel

涂层硬质合金刀具车削奥氏体不锈钢的试验研究

The Hunan Diamond carbide tool limited company CIMS application engineering scheme design and Implementation

湖南钻石硬质合金工具公司CIMS应用工程方案设计与实施

Image detection for carbide tool wear based on laser grating projection is presented.

提出一种基于激光光栅投影技术的硬合金刀具磨损的图像检测方法。

Way to Increase d Carbide Tool Life

提高硬质合金刀具寿命的途径

Additionally, the friction and wear performance of Inconel 718/ carbide tool are also researched.

同时研究了Inconel718与硬质合金刀具材料对偶时的摩擦磨损特性。