The spinning and drawing technology for producing PET fine filaments of filament denier around 1d by the POY-DT process are described as well as the weaving, dyeing and finishing process are introduced briefly.

The water retention property has a fine linear correlation with the square root of the filament denier and the thickness and weight of the fabric;

织物的保水率与纤维线密度的平方根、厚度和克重之间存在良好的线性关系。

A study on the design of denier electronic balance

关于纤度电子秤设计的研究

The Na-Dene language of the Haida people. The British are a sea-going race.

海达族人说的赫胥语。英国人是个航海的民族。

The dendritic structure can be electrodeposited at low current density with Ti4+.

Ti4+的加入使得在较低的电流密度下形成树枝晶；

The results show that increase of extrusion stress may improve the as cast structure and reduce distribution of dendritic structure.

结果表明：增加挤压压力，可以改善铸态组织，减轻枝晶分布；

Dendritic structure which has diverse architectural modeling with well seismic performance is a new structure of the space structure.

树状结构建筑造型多样，抗震性能好，是一种具有生命力的新型空间结构。

Use and study of dendritic structure and giant cast steel node& construction technique for Shenzhen Cultural Center

树枝结构及巨型铸钢的应用与研究&深圳文化中心钢结构施工技术

Influence of electromagnetic stirring on dendritic structure and mechanical properties of low sulphur steel

电磁搅拌对低硫钢枝晶组织及机械性能的影响

Design on the dendritic structure with steel tubes

钢管树状结构设计

The Application of the Dendritic Structure in the Coupling Transformer

耦合变压器在树状网络结构中的应用

In the process of metal solidification, the numerical simulations of the dendritic crystal growth is an important part of materials science field. Its result is practical guiding significance to effectively control the growth of metal materials.

在金属凝固过程中，对枝晶生长过程的数值研究，是当今材料学领域的一个重要分支，其研究结果对有效地控制金属材料的生长过程有一定的实际指导意义。

And as cooling rate was 0. 1 ℃/ s, dendritic crystal precipitated at first in flux, then lamellar crystal precipitated to last of crystallization.

在冷却速率0.1℃／s时，保护渣首先析出树枝状晶体，然后以片状晶体形态析出，直到结晶终止。

Using appropriate process parameters, the Cu-Al-Ni shape memory alloy with good surface quality and unidirectional dendritic crystal was prepared by the self-made ohno continuous casting equipment.

在自制的水平热型连铸设备（OCC）上，采用一定的工艺参数，制备出表面呈镜面，内部组织沿轴向定向排列的柱状组织Cu-Al-Ni形状记忆合金。

The dendritic crystal grains of primary austenite were spheroidized and fined significantly after the alloy slurry flowed through the cooling slope plate.

合金液经倾斜板处理后枝晶状先共晶奥氏体得到了明显细化、球化。

When the crystallization temperature is blow the solidus, non-oscillatory zoning or dendritic crystal and glass mass will be formed.

当结晶温度低于团相线温度时，则形成非韵律环带或枝晶甚至玻璃体；

Since the theory of dendritic crystal growth was not considered in the simulation, these result were some special result under special conditions.

由于本模型没有引用微观研究中关于枝晶的特殊理论，因此可以将这种结果看做是通用模型的一种特殊情况。

Dendritic crystal growth was generated via basic physical model and combined temperature field simulation.

本文使用元胞自动机模型根据最基本的物理学原理和温度场模拟计算耦合，得到了枝晶的生长结构。

Effect of wide change of cooling rate on dendritic segregation of a directionally solidified cobalt-base superalloy

宽变冷速对定向凝固合金枝晶偏析的影响

Results show that the increase of cooling rate can restrain dendritic segregation effectively, especially for easily segregated alloy elements.

结果表明：增大冷却速率可有效抑制枝晶偏析，对易偏析元素其效果更明显；

After homogenizing treatment, the dendritic segregation dissolves into the matrix again.

此外，通过均匀化退火可以有效的消除枝晶偏析。