The device is three groups of groove chambers composed of three deckle boards whose clearances are clamped with two dialysers and both sides of which are accompanied by electrode rabbets.

The article introduces the checking templates in manufacturing the bus body, especially in the design and manufacture of the checking templates that are used in back wall transverse radian, windscreen and windshield rabbet

介绍客车车身制造过程中的检验样板，尤其是后围横向弧度、风窗玻璃和风窗止口的检验样板的设计和制作方法

Objective To explore the protective effects of atrial natriuretic peptide ( ANP) on alveolar type II cells ( AT-ⅱ) in rabbets with acute respiratory distress syndrome ( ARDS) induced by endotoxin ( ET).

目的：研究心房钠尿肽（ANP）对急性呼吸窘迫综合征中肺泡Ⅱ型上皮细胞（AT-Ⅱ）的保护作用。

The front end cover and the rear end cover are fixed by screws and rabbets. Meanwhile, the rotor assembly is fixed.

前、后端盖利用螺钉及止口固定，同时将转子总成固定。

Leak analysis of HP carbomate preheater and tenon jointing seal construction

甲铵预热器的泄漏原因与榫槽密封结构

First, the theory of fretting wear and studies on fretting fatigue were introduced and the parametric method was used in the process of creating the model of dovetail joints in UG software.

本文介绍了微动损伤的机理和微动疲劳寿命的研究方法；利用UG软件对燕尾榫联接结构创建了参数化实体模型；

Fretting fatigue in component& the feature in circumferential dovetail joints

构件微动磨损疲劳&盘上周向燕尾榫槽的特点分析

Study on Numerical Control Mill-tenon Machine for European Fashion Wood Windows

欧式木窗数控铣榫机设计理论

This paper focuses on the design method of firtree tenon/ mortise, the three-tooth firtree joint model is established with parametric method by UG software.

本文通过UG软件对涡轮榫头/榫槽三齿结构进行了参数化建模；

Crack Analysis on Rabbet of Grade ⅰ Turbine Disk of an Engine

某型发动机Ⅰ级涡轮盘榫齿裂纹分析

Thermal elastic-plastic analysis and computer flowchart for turbine blade root fastenings

透平叶根接触榫槽的热弹塑性分析和计算流程

VC++ program design of parametric graph for dovetail joint

基于VC++的燕尾形榫参数化程序设计

JSF Round-hole Pearlite Partition Plank

圆榫及孔公差探讨JSF珍珠岩圆孔隔墙板

Mortise 2 D Stress Intensity Factor Determination by Laser Speckle Method

激光散斑法测定榫槽二维应力强度因子

Flat countersunk double nib bolts Remove hinge retaining nuts from studs.

GB/T800-1988沉头双榫螺栓从双头螺栓拆下固定铰链的螺帽。

Therefore the fixture design in trough processing is an important link.

因此夹具设计是榫槽加工中的一个重要环节。

A mortise joint formed by interlocking tenons and mortises.

通过连锁的凸榫和榫眼制成的榫点。

Analysis of tenon and mortise contact problems by boundary element methods

榫头/榫槽接触问题边界元分析

The experiments showed that the urea-resin adhesive produced a better effect;

试验表明：落叶松材的齿榫接合采用脲醛胶的效果较好；

Creep-Feed Grinding Experiment in Propeller Blade Fir-Shape Tenon of 261P Turbosupercharger

261P涡轮增压器叶片枞树形榫齿深磨试验研究

Crack detection of turbine disc mortise of aero-engine by nondestructive testing

发动机涡轮盘榫齿裂纹的探测