Acute toxicity of combination of Methamidophos mixed with trichlorfon, malathion, ibp, dimethoate and phosmet respectively

Quantitative Analysis of Tricyclazole and IBP by Gas Chromatography

20%三环唑·异稻瘟净可湿性粉剂的气相色谱分析

The cooling effects of CCC is simulated using MPI software. The results show that conventional mold flow analysis software cannot fit the features of CCC cooling system by buried casting methods.

用MPI软件对随形水道冷却效果进行了模拟，结果表明常用模流分析软件不能适应埋铸法的特点。

To help dry the paper, the mold lets the water flow through the small wire squares.

为了使纸干得更快，这个模子会让水通过小的金属丝方块流走。

In this paper we report the analysis of underfill encapsulation between the solder ball, micro-chip and substrate by experiment and3D mold flow simulation.

文中主要探讨了覆晶封装底胶充填时，锡球、芯片及基板间的流动状况。

Experimental study of effects of mold flux on thermal flow of mold copper plate

保护渣对结晶器铜板热流影响的试验研究

In this paper, based on the systematic analysis of the present situation of the sediment mathematical, a 1-D mathematical mold for unsteady flow and a non-equilibrium transportation model of non-uniform suspended load has been established to forecast the erosion and deposition.

本文在系统分析一维非恒定水流和泥沙数学模型研究现状的基础上，结合实际的天然河道冲淤预测的应用目标，建立了一维悬移质不平衡输沙数学模型。

Then the basic process to use Mold flow software to realize the numral simulation of the fusion polymer filling the mould cavity is introduced.

然后重点说明了用Mold flow软件，通过有限元的方法实现熔融聚合物流体充填模具型腔时数值模拟的基本过程。

The distribution of mold flow field can be reflected by readings of thermocouples embedded into the copper plates.

结晶器专家系统上显示的结晶器流场分布可以直接通过镶嵌在结晶器铜板上的热电偶变化趋势来反映。

But the little essential understanding for the feedstock mold flow in MIM and the complexity of nonlinear system leads to the little development of the theory. But It will, no doubt, become an important part of the future research.

但由于在实际中对MIM喂料充模流动的本质认识的限制和非线性系统的复杂性，使得这种理论的发展也受到一定的限制，但无疑它将是未来研究的重要方向。

The mold flow analysis utilizes the computer to simulate dynamic filling process about the injection mold.

模流分析技术是利用计算机对注塑件动态填充过程进行模拟。

D Numerical Simulation on Mold Filling Coupling Fluid Flow and Heat Transfer in the Aluminium Alloy Casting

耦合传热与流动的铝合金铸件充型三维数值模拟

Second, numerical simulation of filling, flow, air pocket, fusion trace, and warp were performed with simulation software Mold flow.

其次，利用仿真软件Mold flow对该注塑件进行充填、流动、冷却、气穴、熔接痕、翘曲等数值模拟。

The characteristics of RTM ( Resin Transfer Molding) process are introduced, the mold filling flow, the gists of process controlling and the method of mold design of RTM to produce high accuracy plane radome are briefly described.

介绍了RTM（树脂传递模塑）工艺的特点，并对RTM法制造高精度飞机雷达罩的充模流动、工艺控制要点和模具设计方法等作了简要的论述。

The mold is made of small squares of wire that hold the shape and thickness of the paper. To help dry the paper, the mold lets the water flow through the small wire squares.

模具由小的正方形的铁丝做成，可以控制纸张的形状和厚度。为了使纸张风干，模具允许水通过铁丝流失。

CAE techniques ( such as plastic products mold flow analysis) are used for the post quality evaluation.

同时，采用产品模流分析等CAE技术对塑胶产品模具开发过程进行后期质量评估。

Control of heat and mass transport in continuous casting mold through swirling flow in immersion nozzle

通过浸入式水口中的旋流控制连铸结晶器中热量和质量的传输

Blowing argon gas had much effects on the mold flow field and temperature field.

向结晶器中吹入氩气后，对钢液的流场和温度场有较大的影响。

Study on Effects of Heat Transfer Coefficient between Polymer and Mold on Melt Filling Flow in Micro Injection Molding

微注塑成型中熔体与壁面间传热系数对充模流动影响的研究

Using CAE to design the mold of micro heat exchanger and optimizing the mold gate, flow runners and the cooling water channels.

采用CAE模拟辅助进行微流道微换热器模具的设计，对模具的浇口，流道以及冷却水道的开设进行的优化。

Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times.

加工窗口分析、它零件的模流分析，检查熔体温度、具温度、塑压力和充填时间。