Electromechanical relays are available in non-latching and latching types.

Most laboratory Methods: Use some type of electromechanical transducers.

多数实验方法都使用某种机电换能器.

Electromechanical design for building decoration is to design the plane electromechanical system.

装饰机电设计是与装饰专业配合,设计机电平面系统(俗称二次机电).

It teaches an understanding of principles and analysis of electromechanical systems.

本课程教导的是对电机系统原理的理解和分析.

Motion controlling technology is the core integral part of electromechanical integration technology.

运动控制技术是机电一体化技术的核心部分.

In early days, there used to be electromechanical relay of induction disk-type .

在早年, 曾是感应盘 式 机电继电器.

Use an adapter to connect the BNC connector to the triax input of the electrometer.

用一个适配器把BNC连接器连到静电计的三同轴输入端.

The damping circuit may already be built into the electrometer or may be an external circuit.

衰减电路可以装在静电计的内部,也可以是一个外部电路.

Usually, this method requires two instruments: a voltage source and a picoammeter or electrometer.

通常, 这种方法需要使用两台仪器: 一台电压源和一台皮安计或静电计.

When using the electrometer ohmmeter, measurement accuracy can be affected by a variety of factors.

使用静电计欧姆计时, 测量准确度会受到各种因素的影响.

The Model 6517 A Electrometer has the Alternating Polarity Method built into a test sequence.

6517A型静电计与变换极性法已被做成一个现成的测试程序.

Therefore, a voltmeter with high input resistance, such as an electrometer, is required.

所以需要使用具有高输入电阻的电压表, 例如静电计.

I've smashed the electrometer.

我把静电计摔碎了.

The ohmmeter uses an internal current source and electrometer voltmeter to make the measurement.

欧姆计使用内部的电流源和静电计电压表来进行测量.

This can be checked by observing the analog output of the electrometer or picoammeter with oscilloscope.

用示波器观察静电计或皮安计的模拟输出,可以对此进行检查.

That's because when zero check is enabled, the input resistance of the electrometer is about 10 M ω.

这是因为当零点检查功能打开时, 静电计的输入电阻大约为10Mω.

More information on the measurement procedure can be found in the instruction manual of the electrometer.

有关测量方法的更详细的信息可以在静电计的操作手册中找到.

The machine adopts closed frame, electromotion handspide for generating pressing force and force motor etc.

该设备采用封闭的立柱结构, 通过力矩电机驱动的螺旋升降机提供所需的压力.

After crank handle, the electromotion should not work because of the switch effect.

取下手摇柄后,由于联锁开关的作用, 电动应不能工作.

Electromotion la version caused by abnormal mainly due a 24 V switching power supply variation load capacity.

变成电动不推版不变态的宾要是由于24V开关电源负载本领变差所致.

Electromotion leaving tremendous pressure mechanism is simple in structure, the failure rate is relatively low.

电动离台压机构最大特点是结构简单, 故障率比较低.