RTL 8019 AS source code with ATMEGA 8515 ( schema ) complete source code, has been tested.

Module level micro architecture design and RTL implementation. Chip level integration.

模块级微架构设计以及RTL实现, 片级整合.

The design includes system level design, RTL level design and logic synthesis.

设计工作包括系统级设计 、 RTL级设计、逻辑综合.

The verification includes RTL simulation, gate level simulation and static timing analysis.

验证工作包括RTL级仿真 、 门级仿真和静态时序分析.

With the introduction of ethernet controller RTL 8910 AS , the initializing, data sending and data receiving programs were deployed.

介绍了以太网控制芯片RTL8019AS.讨论了如何在该模块中实现网卡初始化及网卡收发数据的网络通讯过程.

The hardware platform mainly include AT 89 C 55 with 20 k bytes Flash, RTL 8019 AS and RTL 8029 AS, CPLD EPM 7128 S etc.

硬件平台主要是由内带20k字节Flash的AT89C55,32k字节 容量的RAM62256, 网络接口芯片RTL8019AS和RTL8029AS,做PCI-ISA桥的CPLDEPM7128S等组成.

Creating an effective RTL behavioral model.

建立了一种有效的RTL行为模型.

This paper addresses the Transfer Molding ( RTM ) process. The governing equations of resin flow are presented.

介绍了RTM工艺过程 及特点,给出了树脂渗流控制方程.

A pair of mold is designed for the package case with wall rib by RTM process.

本文为生产特种薄壁加筋结构包装箱而设计、制备了混凝土加固玻璃钢RTM模具.

This paper designs and manufactures the mould for the composite skirt fabricated by bladder-assisted RTM.

本文设计制备了气囊辅助RTM工艺用复合裙模具.

The study of this paper can enlarge considerably the area of application of RTM.

论文的研究对提高RTM制品 质量和拓宽RTM工艺的应用领域具有重要的意义.

Liquid direct processing, and RTM in particular, has been proven extremely successful in the automotive industry.

液体直接注塑工艺中, 尤其是树脂传递模塑(RTM) 工艺在汽车业中的应用, 已被证实相当成功.

The major problems involved in fabricating large, high fiber volume fraction components by RTM, are discussed.

阐述了RTM工艺应用于大尺寸, 高纤维含量构件时存在的主要问题.

The cure kinetic model and kinetic parameters of BMI resin for RTM are studied by DSC.

采用DSC方法研究RTM专用 双马来酰亚胺树脂的固化动力学模型与固化动力学参数.

This product is used primarily for hand lay-up , pultrusion, RTM, and filament winding process, etc.

玻璃纤维缝编短切毡主要用于手糊、拉挤 、 RTM和缠绕等玻璃钢成型工艺.

The resin flow in RTM process for thick section parts was investigated.

针对厚截面构件的RTM工艺过程,研究了三维树脂流动问题.

The impregnation of resin for fiber reinforcement process is a very important phase in RTM.

RTM成型过程中,树脂对纤维增强体的充分浸润是非常重要的一环.

A new implicit numerical algorithm was proposed for mold filling simulation of RTM.

摘要RTM充模分析的隐式方法需要迭代来决定树脂注满的区域.

The monitoring system of fiber Bragg grating for the RTM curing process was established.

提出了RTM工艺 树脂固化过程残余应变布拉格光栅传感器检测新方法.

Malaysia: RTM's Wai FM from Kuching on 7270 kHz-for the Iban and Bidayuh communites in Sarawak.

马来西亚: RTM的 “ 喂”调频从古晋在7270千赫的广播-服务于来自砂劳越的伊班族和比达友族.

Tunable THz Bloch oscillations ( BO ) in the superlattice and THz current oscillations in RTS are investigated.

研究了超晶格中的THz布洛赫振荡和共振隧穿结中的THz电流振荡特性.