The air humidity is also not durable mask important reasons.

The internal partition coefficient of building is the important factor of influencing air infiltration.

建筑物内部隔断系数是影响空气渗透的重要因素.

When the bulb is compressed, an air inlet valve prevents blow back from the nozzle.

带有、无压缩的切换功能.带防止从吹出口吸入灰尘(逆流)功能.

Slowly open vent needle valve just as air inlet opens. Record differential pressure.

当空气进口开启时,慢慢开启排气针形阀. 记录压差.

A cover , including an air cowl , is removably mounted to the housing proximate the air inlet.

外罩, 包括空气通风帽, 被可拆卸地安装在外壳的靠近空气入口处.

Separation of the water supply from the air inlet is accomplished by means a diaphragm seal.

水供应与空气进口的分离通过隔膜密封的方法实现.

In the meantime , the effect of air inlet angle on particle deposition was also researched.

同时, 研究了不同气流进口角对粒子沉积状况的影响.

The fuselage & engine thethe MD 500 D The difference are, self-pressurize fuel takethe air inlet strainer.

机身 和 发动机采用MD500D民用型的设计, 区别在于加装自密封燃油箱、发动机进气道过滤器.

The air admission grill, lower part undergoes the redesign, increased the strength full auxiliary air inlet.

进气格栅, 下部经过重新设计, 增加了力道十足的辅助进气口.

Connect the air inlet hose to the throttle body and the air cleaner.

将空气入口软管接至节流阀体和空气滤清器.

Remove the air inlet hose from the throttle body and air cleaner.

从节流阀体和空气滤清器上拆下气流入口软管.

Turn off supply pressure and observe float drop to open air inlet.

关闭供应压力,观察浮子下降,因此开启空气进口.

The air inlet distributor is a biconical diversion type.

进气分布器为双锥导流式.

Let's make the little air inlet under the front panels.

让我们使小进风口下阵线面板.

The fresh-air inlet was usually the crankcase breather cap.

新鲜空气进口一般是曲轴箱通气盖.

The technical terms air leakage rate and air leakage coefficient are always used in boiler field.

推导并建立了“漏风率”与“漏风系数”的关系公式,以便于换算.

It not only saved cost, but also blocked the air leakage of ventilation system.

既节约了设备费用,又解决了矿井通风系统的漏风问题, 同时又不影响行车运输.

The air leakage on sintering machine affects the technological and economical indexes of sintering process.

烧结机漏风问题直接影响烧结过程的各项技术经济指标.

In case air leakage occurs, please repair or replace the pneumatic components leakage without any delay.

如有漏气现象, 应及时修理或更换有关气动元件.

Remedial measures are suggested for problems like large feeding size, system air leakage etc.

对生产过程中出现的入磨物料粒度大 、 系统漏风等问题提出了解决措施.

Be careful when portage, lest the damage of the valve cause air leakage.

在搬运过程中要轻拿轻放, 以免碰坏气门嘴,产生漏气.