For AB_1 and AB_18, their UV-visible absorption spectra in cyclohexane and surface photovoltage spectra show peaks at 450 nm due to the formation of H-aggregate, which underwent a blue-shift about 30 nm than that of monomer intramolecular charge transfer ( ICT) band in chloroform.

Preparation and Characterization of Monomer Casting Nylon 6 and Its Composition with SEBS Elastomer

MC尼龙6与SEBS弹性体复合材料的制备与表征

MC nylon, is called monomer casting nylon. MC nylon has lots of very good properties, such as light quality, no noise and good mechanical properties, and so on.

MC尼龙（单体浇铸尼龙）具有质量轻、不产生噪音、机械性能好和良好的回弹性等独特性能。

Effect of aided agents amount on mechanical and tribological properties of monomer casting nylon

助剂用量对MC尼龙力学和摩擦学性能的影响

Tests are conducted to study the moisture absorption behavior of carbon fiber reinforced monomer casting nylon ( CF/ MC nylon) composites in four kinds of media.

本文对碳纤维增强铸型尼龙（CF/MC尼龙）复合材料在不同吸湿介质中的吸湿行为进行了研究。

In this dissertation, some fundamental problems on monomer casting nylon have been comprehensively studied.

本文就MC尼龙研究和生产中存在的基本问题进行了系统和深入的研究。

Effects of media on moisture absorption behavior and bending strength of carbon fiber reinforced monomer casting nylon composites

吸湿介质对碳纤维增强铸型尼龙复合材料的吸湿行为及力学性能的影响

The formation of PAM molecules in monomer casting nylon 6 ( MC Nylon) was characterized by means of FT-IR and UV spectra.

通过红外、紫外光谱分析表明了刚性链高分子聚甲亚胺（PAM）在尼龙6中已经生成。

Monomer casting nylon ( MC nylon) composites reinforced by carbon fibers ( CF) are prepared by liquid insitu polymerization, and their moisture absorption behaviors are studied.

采用液态原位聚合法制备了碳纤维（CF）增强浇铸尼龙（MC尼龙）复合材料，研究了其吸湿行为。

Temperature Field of Monomer Casting Polyamide 6/ Kevlar Fiber Composites During Preparation Process

单体浇铸聚酰胺6/Kevlar纤维复合材料制备的温度场分析

In this paper, three different kinds of polyazomethines ( PAM)/ nylon 6 in situ polymerization composites were prepared using the process of monomer casting.

本文利用三种聚甲亚胺的单体与尼龙6单体通过原位聚合反应，制备了三种聚甲亚胺/尼龙6原位聚合复合材料，制备工艺采用浇铸法。

It was found that nano-Al 2O 3 improved the wear resistance of monomer casting polyamide with the optimal content of nan o-Al 2O 3 being 3 wt%.

分析结果表明：纳米Al2O3填料可提高单体浇铸PA6的耐磨性，其含量在3%左右时增强效果最好；

Preparation and properties of monomer casting nylon/ carbon fiber composite

MC尼龙&碳纤维复合材料的制备

Study on Fly Ash Reinforced Monomer Casting Polyamide Composites

粉煤灰增强铸型聚酰胺复合材料的研究

Development of the piston ring made with monomer casting nylon

铸型尼龙活塞环的研制

Tribological properties, wear mechanism and the influence of carbon fiber to mechanical properties of continuous carbon fiber-reinforced monomer casting ( MC) nylon ( CCF/ MCPA for short) were investigated.

研究了碳纤维对CCF/MCPA力学性能的影响以及CCF/MCPA的摩擦学性能和磨损机制。

Study on Toughening Modification of Monomer Casting Nylon

单体浇铸尼龙的增韧改性研究

MICRODETERMINATION OF RESIDUAL ACRYLAMIDE MONOMER IN POLYACRYLAMIDE PRODUCT BY DIFFERENTIAL OSCILLOPOLAROGRAPHY The result showed the detection limited 0.2% by UV to determined residue AM in PDA.

导数示波极谱法测定聚丙烯酰胺产品中微量残余单体研究结果显示，采用紫外分光光度法测试共聚物PDA中残余单体AM，以水为溶剂，测试下限为0.2%；

A water-plugging and profile modification agent was prepared using acrylamide and cationic monomer as main materials, and adding acrylic acid, crosslinking agent and other additives.

以丙烯酰胺、阳离子单体为主要原料，加入丙烯酸、交联剂及其他添加剂，制得抗盐型调堵剂。

A new hydrophobic high strength hydrogel ( HHSH) was synthesized from acrylamide and hydrophobic monomer ( AMC12 S), by means of aqueous solution polymerization.

以丙烯酰胺和疏水单体为原料，过硫酸钾-硫酸亚铁为引发剂，采用溶液聚合法合成了疏水型高强度水凝胶。

The results showed that PAM of both cation type and anion type can be used to improve the performance of sludge dewatering, although the dewatering performance was improved at similar levels, the residual acrylamide monomer in finished water was lower using PAM of anion type.

实验结果表明：对不同浓度的污泥，投加阴、阳离子型PAM均能有效降低污泥比阻值、改善污泥脱水性能，但使用阴离子型PAM，出厂水丙烯酰胺单体含量更低。