Analysis of allowable error in launching air-to-air missile

The allowable error for the most importance of objective.

对最为重要的目标函数，其允许误差应最小。

On the synthesis of the spatial RSSR crank-rocker mechanism in accordance with allowable pressure angle

空间RSSR机构按许用压力角、极限位置和行程速比的综合

The available method for determining basic size of cam mechanism according to its allowable pressure angle is lack of appropriateness.

现有按许用压力角确定凸轮机构基本尺寸的方法欠妥。

The design of minimum sized spacial cam mechanism with a translating follower according to allowable pressure angle

按许用压力角设计最小尺寸的直动从动杆空间凸轮机构

Designing the Geometrical Amounts Oscillating Follower Cam Mechanisms in Accordance with Allowable Pressure Angle

按许用压力角确定摆动从动件凸轮机构的几何尺寸

Allowable pressure angle of cam mechanism

凸轮机构的许用压力角

The Determination of a Cam's Allowable Pressure Angle

凸轮许用压力角的合理确定

The practical problem of the allowable pressure of the proposed bearing layer is discussed.

并探讨了有关建议中提出的桩端持力层容许承载力参考数值的实用问题。

The relative factors are discussed: maximum allowable pressure inside the site, permeating coefficient of of MSW, bio-gas production rate, diameter of the well, etc.

同时讨论了影响控制范围的各主要因素：垃圾层中最大允许压力、垃圾层的透气性能、垃圾的产气速率等。

On the basis of well side investigations, this paper analyses the reasons that sliding sleeve can't open within the range of allowable pressure and proposes corresponding measures.

通过现场实践，分析滑套在允许压力范围内打不开的原因并采取相应措施，在实践中起到了很好的效果。

Design allowable stress of arch dam in China comparing with that in American

中国拱坝设计容许应力与美国的比较

Influence of Lowered High-temperature Allowable Stress on Application of Steel CASE 2180

高温许用应力下调对CASE2180钢使用的影响

The analysis results show that the strength of the axle satisfy the allowable stress requirements.

分析结果表明，该车轴强度满足材料的许用应力要求。

Based on mechanical analysis and testing research, the paper put forward a calculation method of interlayer allowable shear stress and the design method of asphalt pavement considering shear strength.

并且，在力学分析和试验研究的基础上，提出了层间容许剪应力的计算方法和考虑抗剪强度的沥青路面结构设计方法。

Discussion on the Increased Range of Allowable Stress in the Design Code for Industrial Metallic Piping

对工业金属管道设计规范中许用应力提高幅度的探讨

Allowable stress and strength design method of masonry code in the United states& flexure design

美国砌体规范的容许应力与强度设计方法&梁的抗弯设计

As for the calculation, the old allowable stress design method and the more simple formula are adopted, not the present limit condition calculation method and its complicated formula stated in the 《 Steel Structure Design Code 》.

在计算方法上不是采用现行《钢结构设计规范》中的极限状态设计法及其较繁的计算公式，而是采用锅炉行业过去习惯采用的许用应力设计法及其较简单的计算公式。

Ultimate state analysis of carrying capacity and tensile fatigue analysis are conducted according to basic combination of loads effect and standard combination of loads effect respectively. Design of foundation screws through allowable stress design method is presented.

按荷载效应的基本组合进行承载能力极限状态分析，按荷载效应的标准组合进行抗拉疲劳分析，采用许用应力设计法进行地脚螺栓的设计。

Strength Design values may be converted to Allowable Stress Design values.

设计要求、强度设计值可转换为许用应力设计值。

On the part of estimating the financial risk of the allowanced corporation, the most important factor is that payoff period is too long ( 28.1%).

在特许公司财务风险评估方面，最重要者为回收期间过长（28.1%）。