Temperature and mechanics effect measurement of plasma induced by laser ablating hard aluminum

Analysis of the Plasma Radiation Induced by Laser Ablating Al at Low Pressure

低真空时激光诱导Al等离子体辐射分析

The plasma properties of laser ablated metal target in air

脉冲激光烧蚀空气中金属靶产生等离子体的性质

An experimental research and analysis of flowing patterns on ablating shapes

烧蚀形状的实验研究与流态分析

Research on the relation between the ablating rate and surface heating power

固体烧蚀速率与表面加热功率关系的探讨

Effect of light field force on transportation behavior of ablated materials

光场力对烧蚀物时空分布的影响

Laser marking is a kind of technique using heat effect of laser to ablate meterials on object surface so as to leave over permanent press.

激光打标是利用激光的热效应烧蚀掉物体表面材料从而留下永久标记的技术。

Effect of graphitization degree on the arc ablate rate of different cabon slide materials

炭滑板的石墨化度对电弧烧蚀速率的影响

The mutual merge of telecommunications network, radio and television networks, and Internet ablates the original boundary of film and television communication industries, changes the right of communication of audiovisual works, and expands the freedom of acquisition to works.

电信网、广播电视网、互联网相互融合使得原有影视传播产业边界消融，改变了影视作品的传播权内容，扩大了获取作品的自由。

The clamp-like jaws of the radiofrequency ablation devices latch onto a section of heart muscle and deliver a thin, focused line of energy that heats and ablates the tissue.

射频消融装置钳样口钳在心肌上，传导纤细的、聚集成线状的能量灼热并消融组织。

Behavior of the ablative deformation of resin matrix materials at high temperature

树脂基材料的高温烧蚀变形

Study on the Test of Smoke Signal of Ablative Material

烧蚀材料烟雾信号测试研究

Study on factors affecting ablative performance of c/ c Composites

炭/炭复合材料烧蚀性能影响因素分析

Research and development of ablative performance of C/ C composites

C/C复合材料烧蚀性能的研究进展

Finally, we test the velocities of three flyers with ablator of different thickness, the result indicates that we can measure the velocities of flyer which can further calculate the released particle velocities, and validate the verdict of theory and simulation.

最后，实验实测了三种烧蚀层厚度不同的飞片的飞行速度，结果表明飞片法可以测得飞片速度，进而求解粒子速度，而且证实了理论和数值模拟的结论。

In this paper, the study of ablative characteristics of Teflon and a kind of ablator ( AT2) used for the thermal protection system were presented. The study used the means of a CO_2 laser as heating source.

介绍了运用CO2激光加热装置，对聚四氟乙烯（Teflon）和热防护烧蚀材料AT2的烧蚀特性研究。

At last, the results of the theory, the numerical simulation and the experiments are summarized. It is concluded that the thickness of the ablator should try to reach the critical thickness.

最后，我们总结了理论、数值模拟和实验三方面的结果，提出了在不出现严重二维效应和卸载波效应的前提下，烧蚀层厚度应当达到临界厚度的设计原则。

The flyer design emphasizes conceptually and physically separate functions of light collection at a distance from the laser source, light concentration on the ablator, and autonomous steering.

飞行器草图强调了概念上和物理上各自的功能&从远距离的激光源收集激光、光集中在烧蚀材料上和自主操纵方向。

The microstructure and the ablation process of the phenolic ablator reinforced by fiberglass was studied by means of EPMA, XRF and DTA-TG.

本文采用EMPA、XRF和DTA-TG等现代分析测试手段研究了玻璃纤维增强酚醛型烧蚀材料的显微结构及其烧蚀过程。

The results show that three regions of the cross-sectioned ablator appeared after the simulative ablation: char layer, pyrolysis zone and virgin region.

研究表明：烧蚀材料在烧蚀后断面形成三个区域：炭化区、有机树脂热解区和原始材料区。

In chapter five, the results of the experiments are analysed, we draw a conclusion that the thickness of ablator should try to reach the critical thickness.

第五章是实验结果和分析，最终得出了烧蚀层厚度应当尽量达到临界厚度的结论。