An analysis on the dynamic factors deviating belt from centerline and its prevention methods in band conveyor

The rigidity analysis of the air cushion of the air cushion band conveyor

气垫带式输送机的气垫刚度分析

Feasibility of U Model Deep Groove Band Conveyor Used in Power Plant

电厂应用U型深槽带式输送机的可行性

Design and implementation of construction drawings CAD system for band conveyor

带式输送机施工图CAD系统的设计与实现

The band conveyor stopped working.

带式输送机停止运转了。

Improvement on the deep trough of belt conveyor

皮带输送机的深槽改造

Talking about the feed trough of belt conveyor Pipe conveyor

浅谈带式输送机的给料溜槽

At present, the usual design method of pipe conveyor is the same as that of traditional trough belt conveyor in many ways. The different aspect is that the value of running resistance coefficient is larger than that of traditional belt conveyor.

目前，圆管带式输送机各种阻力的计算采用与通用带式输送机的设计计算相同的方法，不同的是主要阻力计算中的运行阻力系数的数值大于通用带式输送机的系数。

On increase in inclination angle of deep trough belt conveyor

深槽角带式输送机增大倾角的机理分析

The calculation of the deep-trough belt conveyor transition length

深槽型胶带输送机过渡段长度的计算

This article introduces the characteristics of gravity roller conveyor, power roller conveyor and other types of conveyors and points out problems that need our attention in selecting a conveyor.

本文介绍了重力辊子输送机、动力辊子输送机和其它辊道输送机的特点及选型时应注意的问题。

The gravity conveyor is popularly used in industry because it is simple in design and no power is needed.

重力式辊筒输送机因其不需动力，结构简单等优点，在短距离物料输送中得到广泛应用。

Discussion on Some Design Problems of the Gravity Conveyor

重力式辊筒输送机设计中若干问题的探讨

It explains the application of BCD apron quantitive conveyor in the loading station of the main shaft, and proposes a reasonable transform methods, states its applied efficiency.

介绍BCD定量板式输送机首次在主井装载硐室的应用情况，并提出合理的改造方案，说明其应用效果。

Application and transform of BCD-25 type apron quantitive conveyor

BCD&25型定量板式输送机的应用和改造

Discussion on Discharging of Declined and Apron Belt Conveyor

大倾角带裙边胶带机卸料方式探讨

Sliding type apron conveyor transports pallets bv means of 2 sliding chains running in the same direction.

滑动式板式输送机是由两条同向运行的滑板链输送托盘。

The conveyor middle trough of the improved for stress analysis, theoretically proved the correctness of the optimization program.

对改进前后输送机中部槽进行应力分析，从理论上验证了优化方案的正确性。

Includes: Two ( 2) Trim saws with one ( 1) automatic cross over conveyor. Students work with a variety of machine tools including the bandsaw, milling machine, and lathe.

包括：带有1组自动横向运输机的2组修边锯。让学生操作各种机械工具如带锯、床和车床。

Study on Heat Transfer Process of Solid Conveying Part of Centrifugal Extruder single-stage pneumatic conveyor dryer

离心式挤出机固体输送段的传热过程研究单段气流输送干燥器

Design and application of pulsating pneumatic conveyor with single knife

单刀脉冲式气力输送装置的设计与应用