Casting Technique for Primary Coolant Piping for Pressurized Water Reactor Power Plant and Its Localization

The reactor vessel constitutes the main part of pressure boundary of primary coolant.

反应堆压力壳构成了主冷却剂压力边界的主体。

Fault of primary coolant circuit equipment in nuclear power plant and the comprehensive intelligent diagnosis system

船用核动力一回路设备故障综合智能诊断系统

Study on Primary Coolant System Depressurization Effect Factor in Pressurized Water Reactor

压水堆一回路卸压措施影响因素研究

Mathematical Model of Primary Coolant in Nuclear Power Plant Influenced by Ocean Conditions

核动力装置一回路冷却剂受海洋条件影响的数学模型

Numerical simulation and analysis of three-dimensional flow in a primary coolant pump

主冷却剂泵三维流场数值模拟与分析

In order to validate performance of the organic carboxylic acid engine coolant, 80000-kilometer road tests of a JETTA CTX car which uses this type coolant are done.

为检验有机羧酸型发动机冷却液的性能，对使用该冷却液的捷达CTX型轿车进行了8万km的道路试验。

This contact risks causing premature wear of the pipe due to chafing, which long term could lead to a leakage of coolant fluid.

这种接触会造成早期的出水管老化，长时间会导致冷却液的泄漏。

It is usually difficulty to obtain film coefficients between the working roll and the coolant fluid as we solve the temperature field of the roll.

工作辊与冷却液之间对流换热系数的确定是轧辊温度场分析的难点。

While the spraying angle of coolant fluid and the distance between the working rolls and the nuzzles have little influence.

对流换热特性对喷嘴与工作辊之间距离的变化不敏感，冷却液喷射角度的变化对对流换热特性有一定的影响。

The simulation results show that the speed, the temperature and the viscosity of coolant fluid exert much influence on convection heat transfer;

结果表明，冷却液喷射速度和温度以及冷却液的粘度变化对对流换热特性有着明显的影响；

The traditional atomizer nozzle is difficult to achieve the desired spraying effects because of the coolant fluid viscosity.

传统雾化喷嘴由于受切削液粘度的影响，很难达到理想的雾化效果。

Right Using Coolant Fluid of Engine

发动机冷却液的正确使用

On the vehicles concerned, the coolant fluid level sensor may be porous.

在该种车辆，冷却液液位传感器可能会是渗水的。

The maximum temperature of the wall decreases with increasing coolant flow.

随着冷却剂流量的增大，推力室壁中的最高温度明显下降；

Experimental study on the coolant flow resistance of control rod channel in research reactor

研究堆控制棒通道冷却剂流动阻力特性实验研究

Numerical Study of Coolant Flow in Engine Block Water Jacket

柴油机缸内冷却液流动数值模拟研究

Four events could result in a decrease of core coolant flow rate.

四种事件可导致堆芯冷却剂流量下降。

Experimental Investigation on the Water Coolant Flow Field of Engine Cylinder Head

发动机缸头冷却水流场试验研究

Numerical analysis of coolant flow and heat transfer in fuel assembly

燃料组件中冷却剂流动与传热的数值分析

Metrology is to ensure the value accurate and consistent. The flow metrology is one components of the metrology science, coolant is mainly used for the cooling of airborne electronic equipment and fire control radar, numerous coolant flow meter need to be calibrated.

计量的目的是保证量值的准确一致，流量计量是计量科学技术的组成部分之一。冷却液主要用于机载电子设备、火控雷达的冷却，大量冷却液流量仪表需要校准。