Application of model 160 double crank camera in strategic range

Optimized of parameters of basic dimensions of double crank shaft mechanism

双曲柄机构基本尺寸参数的优化

A New Design Method of Double Crank Mechanism

双曲柄机构设计新方法

Crank angle between extreme position effects transmission performances of mechanism in crank-slider mechanism directly.

在曲柄滑块机构中，极位夹角θ的大小直接影响到机构的传动性能。

Range of Crank Angle Between Extreme Positions for Planar Four-bar Linkage

平面四杆机构极位夹角的取值范围

Research on Transmission Performances of the Crank Angle Between Extreme Position in Crank-slider Mechanism

极位夹角对曲柄滑块机构传动性能影响的研究

More Analysing and Studying the Definition of Crank Angle between Extreme Positions

对极位夹角定义的进一步分析和研究

Development of Crank Angle 'Window' Controller for IC Engine

内燃机曲轴转角窗口控制器的研制

Each quantity is considered to be a function of the crank angle and radial position in the combustion chamber.

各计算量均作为曲轴转角和燃烧室径向位置的函数；

The transient change of discharge coefficient via engine crank angle is calculated for the first time.

首次计算出连接通道流量系数随曲轴转角的瞬时变化规律。

With the third steps and the fourth steps natural frequency vibration, the smaller close to the second crank arm of crankshaft and round place natural frequency of the main shaft transition the position is.

以第3阶和第4阶固有频率振动，位置越靠近曲轴第二个曲柄臂与主轴过渡圆处固有频率越小。

Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft.

转动雨刷模组盖，并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。

The RW Series Rotary Actuator design utilizes two independent piston cylinders, each piston has a crank arm attached to a crankshaft.

在RW系列旋转式驱动器设计采用两个独立的活塞筒，每个活塞有曲柄连接曲轴臂。

The machining of deep bolt holes in the air compressor's crank arm Machining of Threaded Holes in Engine Con Rods

空压机连杆两螺栓孔的深加工6102柴油机连杆螺栓孔的加工

The crankshaft machining complex lathe turned the crank arm journal with the way of servo turning methods.

曲轴加工复合车床通过随动车削的方式对曲轴连杆轴颈进行加工。

Operations on multi-points are available through the crank arm framework.

多点式操作可通过曲柄臂框架。其结构简单轻便，运作畅顺。

Affix using one of the crank arm fixing bolts.

词缀使用其中的一个曲柄臂固定螺栓。

Then, it introduces CAD model into the finite element software, and accurately calculates bell crank rigidity and fillet stress concentration factor, which is used to analyze subsequent torsional vibration and strength.

将CAD模型导入有限元软件，计算求取准确的曲拐刚度及圆角应力集中系数，用于后续扭振及强度分析。

The bell crank connects to a Tiller handle using a universal joint.

钟曲柄连接到一个使用通用蘖处理联合。

The crankshafts shown in Fig1-4 is actually made up of various parts such as main bearing journals, rod journal, crank arm, bearing, counter balanced weight and flywheel end.

在图1-4中，曲轴实际上由以下不同的部分组成，它们分别是：主轴承轴颈、连杆轴颈、曲轴臂、轴承、平衡配量（？）以及飞轮端。

Reducer, crank pin bearing so small and no reverse impact load that reducer tooth broken, crank pin fracture will not happen.

减速机、曲柄销受力小，无反向冲击负荷，减速机打齿、曲柄销折断的故障不会发生。