Research on Calculation Methods of Bending Resistance Bearing Capability of Reinforced Concrete Beams in Service

Test Research on the Bending Resistance of Segment for Subway Shield Tunnel

地铁盾构管片弯曲变形特性试验研究

Experimental Research on Bending Resistance of Reinforced Concrete Beams

钢筋混凝土梁的抗弯性能实验研究

Being aimed at the stressing and damaging reasons of bridge surface layers, this paper mainly deals with the bending resistance test and wear test of steel fiber concrete materials, analyzes the bending performance of steel fiber concrete, and expounds the wear-resisting mechanism.

针对桥面铺装层的受力状况和破坏原因，重点对钢纤维砼材料进行了抗弯强度试验和耐磨损试验，并进行了钢纤维砼弯曲性能分析，闸述了钢纤维砼的耐磨机理；

It firstly derivates theoretical analysis formula of force and stroke by using beam bending theory and energy method.

首次采用梁的弯曲理论和能量法结合的方法推导了弯曲力和行程的理论解析公式。

A simplified calculation of stair beam bending and deformation

阶梯式梁弯曲变形的简化计算

Beam bending test of RPM pipe and control of beam bending strain in construction

RPM管梁弯曲试验及其梁弯曲应变的工程控制

Testing method for annealing point and strain point of glass by beam bending

玻璃退火点和软化点测定方法-压梁法

Influence of Laser Beam Bending on Thickness Measurement of Hot Steel Plate

光线弯曲对激光测量热钢板厚度的影响

Application of Intelligent Instrument in Beam Bending Normal Stress Experiment

智能仪表在直梁弯曲正应力实验中的应用

Calculation on Large Deflection of Beam Bending Using Numerical Integral Method

计算梁大挠度变形的数值积分法

The study on the experiment of wall thickness deformation of coreless bended small-diameter tube

小直径管无芯弯曲壁厚变形的试验研究

Familiar defects of bended tube and solving methods

常见弯管缺陷及措施

Analysis for stiffness on the bend vibration natural frequencies of a helicopter tail drive system

刚度对直升机尾传动系统弯曲振动固有频率影响的分析

Experimental Studies on the Bend Deformation of Welding Structure

焊接结构弯曲变形实验研究

I went on the bend with an intimate friend.

我和一个知心朋友痛饮了一番。

He promised to give up being on the bend.

他答应不再纵酒胡闹。

The fracture toughness K IC and interphase energy G IC of Ag-Cu/ Ti nan'on bilayer film and Ti monolayer film composite system are tested by unilateral gap three-point bend method and double cantilever beam method.

用单边缺口三点弯曲法和双悬臂梁法分别测试了Ag-Cu/Ti纳米双层膜及Ti单层膜复合体系的界面断裂韧性KIC及界面断裂能GIC。

I had to bend double to get under the table.

我必须弓着身子才能钻到桌子底下。

It drove you to bend back with all your might until your groins hardened, your thighbones pushed up and out, and your lower back arched too deeply.

你尽可能地向后弯曲，直到腹股沟变硬，大腿骨向上、向外推出，下背部过度地深弯。

On your next inhalation, lengthen the back of your neck and bend back slightly to counteract the tendency of your upper trunk to slump.

下一次吸气时，拉长颈部后侧并微微后仰来中和上半身含胸的趋势。