Using finite element method for 16 frame-supported continuous masonry walls composed with the normal law, the paper presentes a simple method of calculating bending moment of control cross section of joists based on Matlab.

However, as a result of domestic equipment and backward technology, the major forms of production of metal wire forming is the labor intensive in our country, that is, using a simple manual wire bending die, and some small semi-automatic forming equipment may be used.

然而由于国产装备技术落后，国内金属线材的成形加工主要以劳动力密集型的生产方式为主，采用简单的手动弯丝模具，加上少许半自动的成形设备。

A simple rectangular plate bending element of rapid convergence

一种快速收敛的简单矩形板弯曲元素

Give an introduction about a simple general-purpose bending die.

介绍了一种简易通用弯曲模设计。

Design of a Simple Fatigue Bending Machine for Plate

简易平板弯曲疲劳试验机的设计

The characteristics of the corner rain eaves parts and their forming principle were analyzed. The compound forming was broken into simple bending and flanging.

分析了角部雨檐零件特点及其成形机理，将复合成形分解为简单的弯曲和翻边。

And the fault-related folds include simple bending structural style, fault-bend folds, back thrust uplift and so on.

其中断层相关褶皱包括：简单摺曲构造样式、断弯褶皱、背冲隆起褶皱等。

The bending fatigue property of every part of the rail

钢轨各部位的弯曲疲劳性能

Effect of Surface Defects on Bending Fatigue Behavior of High Strength Spring Steel

表面缺陷对高强度弹簧钢弯曲疲劳性能的影响

Establish of Gear Bending Fatigue Strength Limit based on BP Network

基于BP网络的齿轮弯曲疲劳强度极限的确定

Bending Fatigue Testing Machine of Automobile Wheel Based on Microcomputer Control

基于微机控制的汽车车轮弯曲疲劳试验机

Open Cross-Section Beams Under Pure Bending ⅱ. Finite Element Simulation

纯弯曲开口横截面梁的有限元模拟分析

Test and Research of Concrete Creep for Beams Under Pure Bending Loads

纯弯曲混凝土梁的徐变试验研究

Strain Damage Failure Analysis and Prediction for Beams under Pure Bending Loads

纯弯曲梁的应变损伤失效分析和预测

Improvement of Experimental Equipment of Pure Bending Normal Stress

纯弯曲正应力实验装置的改进

A Stress Analysis of Damage Concrete Beams Under Pure Bending

损伤混凝土梁弯曲应力分析

Simulation Experiment of pure Bending of beam Based on VB

基于VB的梁纯弯曲电测模拟实验

In a beam type compensator a stress pattern produced by pure bending is frozen into the material.

在梁式补偿器中，其应力光图是由纯弯曲产生而被冻结在材料之中。

Bending modulus of CF/ KF hybrid composites are on the rise with carbon fiber volume fraction increasing.

CF/KF混杂复合材料的弯曲模量随着碳纤维相对体积分数的增加而呈上升的趋势。

Adding GF increased not only tensile strength and bending modulus but also impact strength of the composite.

GF的加入不但提高了材料拉伸强度、弯曲性能，而且提高了其冲击强度；

Investigation of influence factors on bending modulus of carbon fiber/? Epoxy

碳纤维/环氧复合材料弯曲模量影响因素的研究