A General Solution for Solving Elastic Bending Problem of Rectangular Thin Plates

Inland Vessel External Force Calculation with the Correction of Bending Deflection

内河船舶考虑弯曲挠度影响的外力计算

Integration Matrix Method for Calculation of Bending Deflection

弯曲挠度计算的积分矩阵方法

A New Method to Solve the Bending Deflection of Stepped Beams

阶梯形变截面梁弯曲变形的一种新解法

It gave the detail about analyses of bending deflection and strength, compared the results with other methods.

在此基础上，详细分析计算了梁的弯曲变形和弯曲强度，并与采用其他方法得到的结果进行了比较。

The methods of compressing strain energy and bending strain energy are adopted to study low temperature performance of montmorillonite modified asphalt with two different montmorillonites by indoo.

通过两种武汉市售蒙脱土和实验室纯化蒙脱土，采用压缩应变能、弯曲应变能的方法，进行蒙脱土改性沥青低温性能研究。

Series solutions were derived for the in-plane strain, deflection and bending strain that satisfy the simplified boundary conditions to calculate the shear lag coefficient.

根据简化的边界条件，得到了面内应变和弯曲应变的级数解，进而求得剪力滞后系数。

This thesis establishes the mathematical models of measuring angle strain and bending strain, develops the functional relation between the strain and the measuring values.

建立了电磁检测法检测构件弯曲正应变和剪应变的数学模型，推导出应变与时间域计测值之间的函数关系；

The FA reducer pin teeth structure is lying pillow type, so the bending strain may be ignored.

由于FA型减速器针齿采用卧枕式结构，弯曲变形可不计。

Determination of the long-term ultimate bending strain and calculation of the long-term ultimate relative ring deflection, both under wet conditions

潮湿条件下长期环状弯曲应变和长期环形偏转的极限测定

And the influence of bending strain on critical currents and measured losses were analyzed.

分析了弯曲应变对它们的影响。

Measurement and Analysis of Dynamic Bending Strain in Marine Shafting

船舶轴系动态弯曲应变的测量与分析

Teaching of Internal Bending Force in Material Mechanics

材料力学中弯曲内力的教学研究

FEM Analysis of Effect of Bending Force on the Crown of Strip

弯辊力对带钢凸度影响的有限元分析

Synthesizing Method Used in Drawing Diagrams of Internal Bending Force

综合法绘制梁的内力图

Interactive Bending Force of Bridge and Track of High Pier Bridge

高墩桥的桥梁和轨道相互作用的挠曲力

Analysis and modification of hydraulic roller bending force control system

热轧机组液压弯辊力控制系统特性分析与改进

According to the law of crack development and mechanical index correlation analysis results, use the maximum bending force, shearing force and fracture energy as the main mechanical parameters, put forward the test design method.

基于裂缝动态发展规律与力学指标关联度分析结果，以最大弯曲力、层间剪切力和断裂能作为主要设计参数指标，提出配合比设计的试验方法。

This design method can improve dynamic and static characteristics of system by collecting bending force signal, summarizing experience and designing control rule.

通过采集弯曲力的变化信号，总结弯曲经验，制定控制规则，改善了系统的动静态特性。

In hot strip mills, crown and flatness are main targets of profile and flatness control, and bending force of work rolls is one of main control ways in shape control.

凸度和平坦度是热连轧机板形控制的主要目标，多机架工作辊弯辊力则是其板形控制的主要调节手段。

Bow expander roller discussion on the neck bending stiffness of work rolls in the hydraulic bending roll control system

弯辊扩幅机，扩幅弯辊液压弯辊控制中工作辊辊颈弯曲刚度探讨