Causes to roll breakage of two high rolling mill in plate mill and preventative measures

An Analysis of Work Roll Breakage of Tandem Mill

武钢冷轧厂五机架工作辊断裂原因分析及改进措施

Resolution the steel rolling problem of roll breakage with heat ageing method

用热时效法解决轧钢的断辊问题

The roll breakage status and its causes in the First Bar Production Line in last two years have been introduced, and the countermeasures for reducing the roll breakage have been put forward.

分析了棒线厂一棒生产线近两年来发生的断辊情况及原因，并提出了减少断辊所采取的有效措施。

On-line Monitoring of Cutting Tool Breakage in Milling Operation Based on Cutting Force

基于切削力的铣刀破损实时监测技术研究

Study on The In-process Monitoring and System for Tool Breakage

刀具破损在线监测及其系统的研究

Tool Breakage Monitoring System in Automatic Process

自动化加工刀具破损监测系统

At last, the equation of tool breakage model is achieved.

并应用这种方法得出刀具破损模型的方程。方程的确定为刀具破损状态的预报监控奠定了基础。

The On-line Monitoring System Of NC Tool Breakage Using Wavelet Analysis

基于小波分析的数控刀具状态在线监控系统

Investigation on a New Alarm System for Cutting Tool Breakage

一种新的监控刀具破损报警系统的研究

The On-line Monitoring System of Tool Breakage in Numerical Control Cutting

数控切削过程中的刀具破损在线监控

Fiber breakage and its development in fiber reinforced composites

单向纤维增强复合材料中纤维断裂及其发展

The intensifying of carding action often accompanies the increasing of fiber breakage.

加强梳理作用常会引起纤维断裂。

Stress concentrations in a composite sheet due to fiber breakage

复合材料内由纤维断裂引起的应力集中

Wood Influence on Thermomechanical Pulp Quality: Fibre Separation and Fibre Breakage

材种对热磨机械浆质量的影响：纤维分离与裂断

They are fibre breakage, interfacial debonding and fibre breakage plus interfacial debonding, which are correlated with three kinds of interfaces: slight-reaction, fine compound precipitation and coarse compound precipitation interface.

三种断裂类型对应三种不同的界面状态：轻微反应型、细小化合物析出型和粗大化合物析出型。

Modification of conventional sizing dyeing machines with PLC and tension inverter controller improves mech-electronical level, and auto pulling and winding are gained as well as constant winding as a result of reducing the problem of yarn breakage and yarn billow.

老式浆染联合机采用PLC和张力控制专用变频器改造后，提高了机电一体化水平，实现了车头牵引、卷绕的自动控制及恒张力卷绕，避免了崩纱浪纱故障。

It would cause balloon collapse and yarn breakage in ring spinning, should the ring and traveler approach this neck portion.

环锭纺纱时，如果钢领钢丝圈位置逐步接近该气圈颈部就将造成气圈崩溃和纱线断头。

As the average spinning tension was low, the machine load and the yarn breakage were reduced, notable economy benefit could be obtained.

由于平均纺纱张力减小，可降低机器负荷和降低细纱断头率，有显著的经济效益。

FS 2.0 casts on again automatically after a yarn breakage.

FS2.0机能够在纱线断头后自动恢复编织。

Improve Bobbin Surface Design to Reduce Yarn Breakage in Unwinding

改进纱管外形设计降低退绕断头