abrasive的例句大全

The movement locus and its effects on surface quality, productivity, and the abrasion uniformity of the abrasive disk were analyzed.

接着分析行星式平面研磨机的运动轨迹及其对加工表面质量、研磨效率、研磨盘磨损均匀性的影响；

The relative velocity function of the workpiece to the abrasive disk is obtained through kinematic analysis, the material removing function and the lapping uniformity function are deduced based on Preston equation.

在Preston方程基础上，建立了材料去除函数和研磨均匀性函数。

A novel mode of uncertain eccentricity plane lapping is presented, while the workpiece rotates about its own axis, it's revoluting about the axis that is perpendicular to the abrasive disk.

提出了一种新的不定偏心平面研磨方式，主动驱动工件使其在绕自身回转轴自转的同时，绕垂直于研磨盘表面的轴线公转。

The effect of varying mates on abrasive wear character of martensitic wear-resistant steel by MLD-10 type impact abrasion tester was investigated.

讨论了在动载三体磨粒磨损条件下，马氏体钢配副变化对磨粒磨损系统耐磨性的影响。

The micro-scale abrasive wear behaviors of TAMZ alloy were studied using a TE66 micro-scale abrasion tester.

采用TE66试验机对新型TAMZ钛合金的微磨粒磨损行为进行了研究。

By Make experiment of plunger case surface abrasion hardness, in the last, adopt high strength engineering plastic to act as anti-abrasive material, make the success, get great result.

通过对柱塞的表面耐磨层进行各种试验，最后采用了高强度工程塑料进行压注试验，取得了成功，效果显著。

All Meguiar's waxes are non-abrasive, this means Meguiar's waxes contain no ingredients that will abrade the paint or instill a scratch.

所有的美光的蜡都是非研磨性质的，它不含可能磨损车漆或制造潜划痕的污染成分。

Discussion on Yarn Abrasive Test and Yarn Abrader

纱线耐磨试验与测试仪器的研究

Development of Coated-Abrasive Abrader for Inner Walls of Crankshaft Finishing Boot

曲轴抛光靴内壁砂带研磨机床的研制

Investigation of properties and mechanism of abrasive wear of boride layer

硼化物层的磨料磨损特性及磨损机理

Cubic borazon has been developed as an ideal hard abrasive due to its high hardness, high thermal stability and high chemical inertia properties.

立方氮化硼因其具有三高特性，而成为一种理想的硬磨料得以发展。

Proper hardness, abrasive ability, high efficiency of polishing, well precision.

硬度适中, 耐磨性好, 抛光效率高 、 精度好.

Air conveyer flume is a pneumatic conveying equipment featuring less energy consumption, less abrasive, change in powder conveying direction, multipoint feeding and multipoint discharge.

空气输送斜槽是一种能耗小、磨损少，可改变粉料输送方向，可多点喂料、多点卸料的气力输送设备。

Special varieties of grinding with sintered corundum abrasives such as abrasive and fiber.

特殊品种的磨具有烧结刚玉磨具和纤维磨具等。

The dental abrasive testing machine applies a V-like swing arm to driving the wearing part to move along the slope back and forth, which is connected with an eccentric wheel fixed on the crankshaft of the gear motor through a connecting rod.

该机采用V形摆动臂来驱动磨耗部分沿斜面作往复磨耗运动，V形摆动臂通过连接杆与减速电机轴上的偏心轮连接。

The new kind of CSD diamond abrasive with the crumb structure which consists of many fine crystals has the character of coarsen and scraggy surfaces, it can avoid that single cystals early fall off because of the fast-ness in the bonder;

由多个细小晶粒构成的团粒结构的GSD金刚石磨料新品种，具有表面粗糙、凸凹不平的形貌特征，且在结合剂中把持牢固，避免了单晶磨料过早脱落的现象，使得磨具寿命成倍提高；

Taking into consideration all the requirements based on the design of a high pressure water abrasive cutting nozzle, and a number of dimensions is analyzed.

综合考虑各种要求的基础上设计了一种高压水切割用磨料喷头，并对一些尺寸参数进行了分析。

Squirt a generous amount of cream cleaner onto the abrasive side of a house hold sponge. Then get scrubbing.

向家用海绵有研磨料的一面挤上大量清洁剂，然后擦洗。

The basic theory and characteristics of superfinishing technology using abrasive stones are introduced.

介绍了油石超精技术的基本原理和特点.

The general electroplating CBN honer surface is point contact engagement with the gear surface in the process of cutting, thus the cutting efficiency is low and the CBN abrasive is wasted.

珩齿加工过程中，普通电镀CBN珩磨轮的齿面与被加工齿轮齿面是点接触啮合，因而加工效率低且造成CBN磨粒的浪费。