centrifugal的例句大全

The model of the aluminum alloy wheel classified as 16 x 6.57 is built. Static stress analysis is carried out to study the influence of bolt pre-tension, centrifugal force and the cornering force to the structural as well as the distributing rule of stress and strain.

首先根据试验工况建立起16×6.5J车轮的有限元模型，通过静力分析研究螺栓预紧力、旋转离心力和试验弯矩对车轮结构强度的影响以及车轮结构的应力应变分布规律。

In the paper, model of ballast pump is established according to the principle of centrifugal pump.

本文根据离心泵的原理建立了压载泵流量模型；

Thermodynamic Performance Test System of Centrifugal and Axial Blower and Compressor

透平式鼓风机及压缩机热力性能测试系统

The design principal, system construction and function requirement of centrifugal and axial blower and compressor is introduced.

介绍了透平式鼓风机及压缩机热力性能测试系统的设计原理、系统结构和功能要求。

Various common troubles of rotor, bearing, impeller, mainshaft and non-rotatable parts of centrifugal gas blast blower were analyzed systematically.

系统地分析了离心式煤气鼓风机转子、轴承、叶轮、主轴、非转动部件等各种常见故障。

Predictive Method of Fault Occurrence Time of Centrifugal Blower Based on Neural Network

一种基于神经网络的离心式鼓风机故障发生时间预测方法

Practice of increasing capacity and improving efficiency and wear behavior of centrifugal blower

关于离心式鼓风机增容、增效及提高耐磨性的实践

Study and practice on Noise Control of Large Centrifugal Blower

离心鼓风机噪声治理研究与实践

Computer Control System of GM Centrifugal Blower Unit Based on PLC

基于PLC构成GM离心鼓风机组的计算机控制系统

No surface blowhole formed in cast pipe when the amount of gas evolution from the coating of pipe model for water-cooled centrifugal cast was less than 5.5mL/g.

当水冷法管模涂料发气量≤55mL/g时，铸管表面不产生气孔缺陷。

Application of High Voltage Inverter in Centrifugal Booster Compressor

高压变频器在离心式循环压缩机上的应用

Flowing model and analysis of waterpower loss inside turbine casing of centrifugal pump

离心泵蜗壳内的流动模型及水力损失分析

A Higher Order Sound Modal Analysis of the Volute Casing of a Centrifugal Fan with a Sound-Soft Boundary

声软边界离心风机蜗壳高阶声学模态分析

Flow field of centrifugal pump ( Pump flow passage includes suction pipe, impeller and volute casing.) was obtained by solving the Reynolds average Navier-Stokes equation.

通过求解包括进水管、叶轮、泵体等过流部件在内的水泵流道内的三维稳定雷诺平均Navier-Stokes方程，获得水泵内部的流场分布特征。

An investigation on the design parameters of the centrifugal seed feeding apparatus

对离心式排种器设计参数的探讨

Centrifugal pump in the assembly must be well prepared.

离心泵在装配前,必须做好准备工作.

Based on the analysis and numerical results, the physical mechanism of thermal drive in centrifugal fields is advanced, and a dimensionless parameter group is suggested to measure the relative importance of buoyancy and rotation to the mean equivalent conductivity.

通过方程分析和数值模拟提出了离心力场热驱动流的物理机制以及自然对流和旋转流相对作用大小的判别依据；

The whole centrifugal pump system, including leading-in conduits, blades, pump housing, and discharging tube, was calculated using the multi-reference coordinate and standard k-ε turbulent model.

选用多重参考坐标系及标准k-ε湍流模型，计算对包括导入管、叶轮、泵壳及出水管在内的整个离心泵系统。

Influence of Distributing Parameters of Reinforcing Ring on Stress of Centrifugal Drum

加强箍分布参数对离心机转鼓应力的影响

Frequency speed control of centrifugal dosing pump

离心式投药泵的变频调速调节