crankshaft的例句大全

Bispectrum Analysis for Vibration Data of Crankshaft Bearing in Diesel Engine

柴油发动机曲轴轴承振动信号的双谱分析

Numerical Research on Friction Properties of Crankshaft Bearing in an Internal-Combustion Engine

内燃机曲柄滑动轴承摩擦性能的数值研究

Study on the Influences of Some Parameters on the Lubrication Properties of Crankshaft Bearing

若干参数对内燃机曲柄滑动轴承润滑特性的影响

L27/ 38 crankshaft folding defects mould key parameter optimization was researched, and through comparative analysis reasonable Die key parameters were obtained.

针对L27/38曲轴锻件折叠缺陷进行了模具关键参数优化，通过对比分析得出合理的参数选取范围。

Remove and discard the front crankshaft oil seal.

拆下并抛弃曲轴前油封.

Install new front crankshaft oil seal.

安装新的前曲轴油封.

Modeling of 3-D Vibration of Engine Crankshaft& Base on Quadratic Timoshenko Beam Element

内燃机曲轴振动特性的三维模拟&基于二次Timoshenko梁单元

Heavy crankshaft is the key component of gas engine.

大型曲轴是大型内燃机的关键部件.

Research on Underslung Heat Treatment Product Line for Crankshaft

悬挂式曲轴调质热处理生产线的研制

Connecting with the actual production process , crack formation in ZG 35 CrMo crankshaft is analyzed.

结合生产实际分析了ZG35CrMo钢曲轴裂纹的形成原因,提出了预防与消除裂纹的措施.

Then turn crankshaft by360 °± 27 ° and adjust the intake valves and exhaust valves which are originally in their unadjustable positions.

转动曲轴360°±27°，调整原先处于不可调位置的进气门和排气门。

If chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets.

若正时链不令人满意，则拆下凸轮轴链轮固定螺栓，并拆下曲轴和凸轮轴链轮的正时链。

Study of the Influence on Fatigue Strength of Thermal Spraying Crankshaft Roughening by Wet Blasting and Arc

液体喷砂和电拉毛粗化处理对热喷涂曲轴疲劳强度影响的研究

Influence Analysis of the Thickness of Crank Web on Strength of Crankshaft

曲柄臂厚度对曲轴强度的影响分析

Calculation and Analysis on the Deflections of Crankshaft under Dynamic Balancing Test

曲轴动平衡试验中的挠曲变形计算及分析

Optimization Design of Crankshaft Balancer of Piston Compressor Based on Pro/ Engineer

基于Pro/Engineer的活塞式压缩机曲轴平衡块优化设计

Application on Fillet Rolled Nodular Cast Iron Crankshaft in the Diesel Engine

圆角滚压球铁曲轴在柴油机中的应用研究

Clean crankshaft flange and crankcase bore carefully.

小心地清洁曲轴法兰和曲轴箱孔。

Fit the vibration damper on the crankshaft flange.

将减震器安装在曲轴法兰上。

Clean crankshaft flange carefully using acetone or solvent naphtha.

使用丙酮或溶剂石脑油仔细清洁曲轴法兰。