crankshaft的例句大全

If customer complaints are received regarding the aforementioned noises on an engine manufactured before the specified date of introduction, the crankshaft bearing housing must be replaced instead of replacing the complete engine.

如果收到有关发动机产生上述噪音的客户投诉，并且发动机的制造日期早于指定的推出日期，则必须更换曲轴轴承壳，而不是更换整个发动机。

Clean crankshaft flange carefully using acetone or solvent naphtha.

使用丙酮或溶剂石脑油仔细清洁曲轴法兰。

Fit the vibration damper on the crankshaft flange.

将减震器安装在曲轴法兰上。

Clean crankshaft flange and crankcase bore carefully.

小心地清洁曲轴法兰和曲轴箱孔。

Coat the sealing ring inside and out with fresh engine oil and pre-position it on the crankshaft flange.

用新鲜机油涂抹密封圈内外侧，并预先放在曲轴法兰上。

Carefully remove smaller edges or burrs on the chamfer of the crankshaft flange with an oilstone if necessary.

如有必要，请用油石仔细去除曲轴法兰倒棱上的小边或毛刺。

Crankshaft is a key part of Press Machine.

曲轴是曲柄压力机的关键零件。

Crankshaft is the key component for the diesel engine of large ships.

大型曲轴是大型船舶发动机的关键零件。

Heave crankshaft is the key component of diesel engine.

大型曲轴是柴油机的关键部件之一。

A crankshaft, a key part of automotive engine, can influence the quality and life of an automobile.

曲轴是汽车发动机关键零件之一，其性能直接影响汽车的质量和寿命。

Crankshaft is the key energy conversion part in emulsion pump and the best complex component in the processing techniques.

曲轴是乳化液泵能量转换的关键元件，同时也是加工工艺最为复杂的零件。

By precise and automatic measurement, fewer cost and higher efficiency may be brought to the production of engine crankshaft, a key part in engine that holds complex structure and requires high precision in dimension.

发动机曲轴结构复杂，尺寸精度要求高，检测难度大。对其进行自动精确的检测可以提高效率，能显著降低生产成本。

L27/ 38 crankshaft folding defects mould key parameter optimization was researched, and through comparative analysis reasonable Die key parameters were obtained.

针对L27/38曲轴锻件折叠缺陷进行了模具关键参数优化，通过对比分析得出合理的参数选取范围。

Application on Fillet Rolled Nodular Cast Iron Crankshaft in the Diesel Engine

圆角滚压球铁曲轴在柴油机中的应用研究

Optimization Design of Crankshaft Balancer of Piston Compressor Based on Pro/ Engineer

基于Pro/Engineer的活塞式压缩机曲轴平衡块优化设计

Calculation and Analysis on the Deflections of Crankshaft under Dynamic Balancing Test

曲轴动平衡试验中的挠曲变形计算及分析

Influence Analysis of the Thickness of Crank Web on Strength of Crankshaft

曲柄臂厚度对曲轴强度的影响分析

Study of the Influence on Fatigue Strength of Thermal Spraying Crankshaft Roughening by Wet Blasting and Arc

液体喷砂和电拉毛粗化处理对热喷涂曲轴疲劳强度影响的研究

If chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets.

若正时链不令人满意，则拆下凸轮轴链轮固定螺栓，并拆下曲轴和凸轮轴链轮的正时链。

Then turn crankshaft by360 °± 27 ° and adjust the intake valves and exhaust valves which are originally in their unadjustable positions.

转动曲轴360°±27°，调整原先处于不可调位置的进气门和排气门。