drill的例句大全

The article particularizes the theory, configuration and use ways of turnover drill press clamp under the control of PLC. And finally shows the trapezoid drawing of PLC and hydraulic pressure chart.

详细说明了基于PLC控制的自动翻转夹具的原理、结构和使用方法，并结合实例给出了PLC的梯形图和液压原理图。

By reviewing the development of tunnel drill-blasting technology in Taiwan, this paper discusses the blasting theory, contractual affair and engineering practice.

本文回顾台湾地区隧道开炸技术之演进，探讨爆破理论、合约制度以及开炸作业实务等方面的发展。

Convolution Method of Analysing Drill String Test Pressure Restoration

DST压力恢复分析的卷积法

The Development and Application of Wire-line Coring Tool for Placer Drill

砂钻绳索取心钻具的研制与应用

The paper introduces some methods of constructing bunker by the sinking stage lifted with manual calabash. After using the counter-well drilling machine drill hole to brush in a big way, carrying on permanently support again;

长段掘进煤仓，喷射混凝土临时支护，用手动葫芦升降永久支护混凝土砌壁工作盘进行煤仑施工。采用反井钻机钻孔后刷大，再进行永久支护；

Punch Processing of Drill Socket Notches

钻头套缺口的冲裁加工

The Design and Application of Mechanically Fixed Counterbore Drill

机夹扩孔钻的设计与应用

Measurement Method and Experimental Research on Dynamic Force Behavior of Bottom Drill String counterbore with guide

底部钻柱动态力学特性测量方法与实验研究有导柱的平底扩充孔钻

Improvement and optimization of titanium alloys countersink drill

钛合金锪钻改进与优化设计

Application of Floating Positioning Countersink Drill

定位浮动式锪刀的应用

The plan that the falls blasting by prefab coyote hole primarily, and demolition the both sides drill hole scrap for auxiliary is used in ⅲ-phase RCC cofferdams in the Three Gorges Project, in which prefab coyote blasting attract more attention especially.

三峡工程三期RCC围堰采用以预置集中药室倾倒爆破为主、两端钻孔炸碎爆破为辅的拆除爆破方案，其中预置集中药室的围堰爆破尤其令人关注。

Brain biopsy of 70 cases by small cranial drill in neurological medicine

神经内科小颅钻行脑组织活检70例分析

Conclusion it was cure intraventricular hemorrhage, available approach that cranial drill hole, infuse urokinase into ventricle haematoma intracavity and put tube persistent outside drainage.

结论：颅骨钻孔、脑室血肿腔内注入尿激酶置管持续外引流是治疗脑室内出血的有效方法。

Diagonal cut rock drill plus bits Cross recessed pan head screws

对角十字形岩石钻头GB/T818-1985十字槽盘头螺钉

Part of the crack is cut by drill, the crack surface is dust-colour under naked eyes.

钻孔截取裂纹局部，肉眼可见裂纹表面呈暗褐色。

Diagonal cut rock drill plus bits cross-bladed chisel bit

对角十字形岩石钻头

The solving method for main cutting edge and grinding principle for flank of non coaxial helical micro drill point is described.

介绍了主切削刃的求解方法以及非共轴螺旋面钻尖后刀面的刃磨原理；

This article focused on drilling in the actual processing of microporous main cutting edge of micro-drill breaks and microporous processing accuracy.

集中论述了在实际微孔钻削加工过程中主切削刃对微钻头折断和微孔加工精度的影响。

The apparatus and method for testing the thrust and torque on the main cutting edge and chisel edge of drill point was introduced.

通过试验测试了任意形状钻头切削刃的轴向力和扭矩，为钻头受力预测提供了一套完整的研究方法。

Succeeding screen 5.12 Collecting the drill cuttings at the shale-shaker.

到振动筛处取点钻屑来。