heat的例句大全

The principle component is the steam chest or other means of introducing heat efficiently into the product to accomplish boiling.

基本组件是蒸汽密闭箱或者是能够有效的产生热使之汽化的装置。

Application of power generation technology with saturated steam in waste heat utilization system

饱和蒸汽发电技术在废热利用系统中的应用

Heat is used to raise steam which either turns a turbine or forces a piston to move up and down in a cylinder. chamber, combustion, for turbojets or turbopropellers

由热产生的水蒸气或者使涡轮旋转或者使活塞在气缸中上下运动。燃烧室，用于涡轮喷气发动机或涡轮螺旋桊发机

Based on EDS and SEM analysis of metal corrosion surface, the course of contact corrosion between aluminum alloy, structural steel and basaltic microfiber heat-resistant materials were proposed.

通过对铝合金、结构钢等金属接触腐蚀表面的EDS成分分析和SEM微观形貌分析，探讨金属材料与玄武岩微纤维隔热材料接触腐蚀的原因。

The factors of influence on shear strength of heat curing silicone rubber/ aluminum alloy were studied.

研究了影响热硫化硅橡胶与合金铝粘合剪切强度的几个因素。

It is good for the emanatory of crystallization latent heat and the improvement of the radical resistivity in the crystal.

提出石墨在生长过程中由结晶潜热引起棱面与基面的温差是影响其生长形态的重要因素。

On-line Determination of Cumene Hydroperoxide Concentration in Cumene Oxidation Products by Liquid Ultrasonic Velocimeter The Failure and Countermeasure of Heat Exchange Tube in Cumene Oxidation Tower

超声波液体声速仪在线测定异丙苯氧化液中过氧化氢异丙苯的浓度异丙苯氧化塔内换热管的失效与对策

The way of raising foundry cupola heat efficiency

提高铸造化铁炉热效率的途径

According to the determination and calculation result of beat equilibrium of a few cupola with different capacity, this paper analyses and studies the effective way of raising foundry cupola heat efficiency.

根据几座不同熔化能力化铁炉的热平衡测定与计算结果，分析研究了提高化铁炉热效率的有效途径。

TGA analysis showed that the cured product has a initial decomposition temperature and the end of temperature of 329.4 ℃, 417.5 ℃, which demonstrate that this new epoxy resin have good heat resistance.

用热重分析的方法分析了在此条件下固化产物的分解温度和终止温度分别为329.4℃和417.5℃，这表明所合成的新型环氧树脂具有良好的耐热性能。

According to the different industries, the requirements for epoxy curing agents are not the same. Excellent performance of the epoxy curing agent can make the cured product has good stability, high heat resistance and corrosion resistance effect.

根据各行业的不同需求，对环氧树脂固化剂的要求也不尽相同。性能优良的环氧树脂固化剂可以使得固化产物具有稳定性好、耐热性高、抗腐蚀效果好等特点。

Study on Blend Vulcanization System of Heat Curing Silicone Rubber

热硫化硅橡胶并用硫化体系的研究

Study on Thermal Stability of Heat Curing Fluoro silicone Adhesive

热固化铜粉导电胶的研究热硫化型氟硅橡胶胶粘剂的耐热性能

Study on Improvment of Heat Curing of Coal Ash Cement Bonded Particleboard

粉煤灰水泥刨花板热养护工艺改进的研究

Elastic and unelastic characteristics of concrete works in condition of damp heat curing

湿热养护条件下混凝土材料的弹性及非弹性特征

Electron beam curing of resin matrix composites is a cost effective method compared with conventional heat curing.

与普通的热固化方法相比，树脂基复合材料的电子束固化是一种成本有效的固化方法。

Research on the Convection Heat Transfer of the Free Section and Top of a Staggered Cylindrical Array

叉排圆柱阵列自由段及顶端对流传热研究

Cold Model Experiment and Heat Transfer Research of Cyclonic Current Tubes for Film Deoxidizer

膜式除氧器旋流管的冷态模型试验与传热研究

The conditions of optimal heat transfer of the cyclonic current tubes are obtained on the basis of the cold experiment of cyclonic current tubes for film deoxidizer and the analysis of the test result.

根据膜式除氧器旋流管的冷态试验及对试验结果的分析，得出了旋流管处于最佳传热工况的条件。

In addition, cut hardness decreases, heat affected zone width reduces and the size of grain gets smaller during underwater cutting.

超声频脉冲的作用还使得水中切割时切口硬度降低，热影响区宽度降低、晶粒变细小。