inlet的例句大全

Never swap gauges or inlet fittings, and never change gas service.

禁止交换量表或入口配件, 禁止改变气体设施.

The unit is composed of inlet outlet hopper sieve, motor vibrator and frame.

该机由进出料斗筛部 、 电机振动部、机体座三大部分组成.

Finished work every day, we must close the tank inlet valve.

每天工作完毕, 必须把水箱进水管阀门关闭.

After working, close the gas bottle or inlet valve and adjust pressure valve to be relax.

工作结束后, 应关闭气瓶或管路进气阀门,逆时针旋转调节把手,使之旋到松弛状态.

The design of inlet in the rooftop of double-layer ventilation should accommodate with long-time metrological data.

欲设计 双层 通风之屋顶型式,建议配合 长期 之气象观测以决定顶楼钢架通风口的设计型式.

A new casting technology for inlet manifold in tilt casting machine gravity die casting was described.

介绍了在可倾式金属型浇注机上制造进气歧管的铸造新工艺.

Lower manhole, smoke vent, cold – blast inlet, transition pipe telescoping pipeline, etc.

下部人孔 、 烟口 、 冷风口入口 、 转折管 、 变径管等.

The basic principle and one-dimensional mathematic model of MagnetoHydrodynamic ( MHD ) controlled inlet were presented.

阐述了 磁控 进气道的基本原理,建立了一 维 数学模型.

Its reactor has nozzles on side wall and material inlet and outlet.

反应器的两侧壁上装有喷嘴,上、下分别设有进料口和出料口.

During the three types of struts, the performance of inlet with rhombic struts is excellent.

在三种形状侧向支柱中, 采用两端削尖支柱形状的进气道的性能最优.

RTD curves became narrower and more symmetrically regular as the number of inlet channels increased.

随着进口通道的增加RTD曲线变窄并且变得对称.

The controller for swash plate of aircraft inlet is a typical hydraulic serve position control system.

飞机进气道斜板控制系统是一种典型的电液位置伺服系统.

The toll is paid at an inlet to the superhighway.

在高速公路的入口处付过路费.

Calculate the pressure difference by subtracting the desired outlet pressure from the maximum inlet pressure.

通过从最大进口压力减去所需要的出口压力来计算压差.

With different layout of inverted siphon pipe, requirements for inlet flow pattern and submergence are various.

不同的倒虹吸管布置型式, 进口流态及淹没要求有所不同.

Working medium inlet and exhaust non-return valves balance hole for Stirling engine is introduced.

对热气机工质进排气 单向阀 平衡孔作了简介.

The test cock is on the inlet side of the shutoff valve.

测试旋塞位于关闭阀的进口一侧上.

Experimental studies have been pressurecollection efficiency of a cyclone separator with different inlet vanes.

旋风铣削法是一种较先进的高效率加工螺纹方法,适用于批量较大的螺纹粗加工.

When mounting the fan, insure that the inlet is unobstructed and higher than the winch.

当越来越多的球迷, 确保入口的畅通,并高于绞车.

Pitch all horizontal inlet lines toward the stream trap to help eliminate potential water hammer problems.

定位朝向疏水阀的所有水平入口管道,这有助于消除可能产生的水锤问题.