joint的例句大全

TEM study of bonding layer in Cu-Al explosively welded joint

Cu－Al爆炸焊结合层的透射电镜研究

We report a case of vanishing bone in the elbow joint and carpal bones following trauma.

吾人报告一个在创伤后肘部与掌骨骨头消失的病例。

The Fuzzy Reliability Design about the Bolt-joint Set of Engine Bonnet

内燃机缸盖螺栓组联接的模糊可靠性设计

Sacroiliitis probably initiated with bone marrow inflammation, followed by pannus formation, subchondral bony plate destruction, and cartilage degeneration/ erosion, eventually leading to fibrosis, ossification and joint fusion.

SIJ炎可能自骨髓开始，继而血管翳形成，软骨下骨板破坏，软骨变性、破坏，最后纤维化、骨化而导致关节融合。

Radiological features of knee joint were bony spur or bony bridge, osteoporosis, incomplete and thickening articular surface with sclerosis and deformation, degenerative disorders.

膝关节主要为骨刺或骨桥形成，受累关节骨质疏松、关节面不平整、增厚、硬化变形及呈退行性改变。

The Cause and Prevention of Knee Joint Injury in Hexagram Boxing Exercises

太极拳运动中膝关节损伤机制和预防

Analysis of the microstructure of the electron beam brazed joint

电子束钎焊接头组织分析

Study on Interface Fracture Mechanics of Brazed Joint

钎焊接头界面断裂力学试验研究

The shearing strength of the brazed joint can be also greatly strengthened.

同时还可以显著提高钎焊接头的抗剪切强度。

Microstructures characteristics and properties of solidified aluminum alloy brazed joint

铝合金钎焊凝固接头的组织特征和性能

Analysis of transformation-diffusion brazed joint

相变-扩散钎焊工艺焊接接头缺陷分析

Microstructure of Brazed Joint of Bilayer Ceramic Composite and Steel

双层陶瓷复合材料与钢钎焊接头界面的微观组织结构

Effect of Specimen Size on the Residual Stress of Al_2O_3 and Nb Brazed Joint

试样尺寸对Al2O3陶瓷/Nb钎焊接头应力场分布的影响

The results suggest the joint is not ideal if the Cu layer is too thin or too thick, and it is very important for existing some eutectic substance in brazed seam.

研究表明，Cu层的厚度太薄或者太厚，其连接效果都很不理想，同时在Al合金与Cu中间层接触反应钎焊中，钎缝区存在适当的液相对于提高接头强度是至关重要的。

The simulation mentioned above was confirmed by series experiments, and the proper thickness of the brazed seam is 50~ 80 μ m for the CRB joint of Al with Si as an interlayer.

在试验证明FEM计算结果的可靠性的基础上，给出了Si为中间层进行LF21铝合金接触反应钎焊时，其合适的钎缝宽度范围是50～80μm。

The brazing-ability and quality of brazed seam of 6063 aluminum alloy brazed by Al-Si eutectic filler metal and QF flux is discussed by means of test of spread-ability and test of T joint.

本文用平百铺展试验和T型接头试验，研究了6063铝合金采用AI－St钎料和氟化物钎剂（QF钎剂）钎焊时的钎焊性和钎缝质量。

Study of Heat Treatment Technics on Carbide Joint by High Frequency Induction Brazing

高频感应钎焊硬质合金接头热处理工艺研究

Experimental Research on Torch Brazing Solder for Al-Cu Joint Welding

铝－铜火焰钎焊材料研究

Joint strength and fracture analysis of arc brazing with Cu based filler metals

Cu基钎料电弧钎焊接头强度及断口分析

Interface Behavior and Joint Strength by TIG Arc Brazing for Titanium and Titanium Alloy

钛及钛合金电弧钎焊及接头强度