parameters的例句大全

The angle only data error is treated as mini disturbance of parameters and the sensitivity analysis model ( fhp) on nonlinear programming is established in the case without disturbance.

测角观测误差看作为参数的微摄动，而非线性规划的灵敏性分析模型（fhp）建立在无摄动的情况下。

Based on experiment, the influence of the process parameters of fluid Jet polishing ( FJP), including working pressure, working distance, jet angle and working time etc, on the removal rate of the workpiece is investigated.

以实验为基础，研究了液体喷射抛光技术的各工艺参数，包括喷射角、工作压力、工作距离和作用时间等参量对工件材料去除的影响。

The surface shape of the workpiece is exactly modified by controlling the parameters of FJP, such as pressure, direction, working time etc.

通过控制液体喷射的压力、方向及驻留时间等量来定量修正被加工件面形的新型光学加工工艺。

This paper analyzes and computes several FLR model, then use the best model to calculate the corresponding parameters.

同时，文中分析了几种场限环结构模型，对它们做出了数值分析，在得到了最佳模型后，计算相应的参数并制出相应的版图。

The effects of flunarizine ( FNZ) and/ or vitamin C ( Vit C) on the above parameters were observed.

进而观察盐酸氟桂嗪（FNZ）和／或维生素C（Vit C）对上述各指标的影响。

This paper presents a prediction model of frequency parameters of short-wave communication based on-singleton fuzzy system.

提出一种利用非单点模糊系统建模的 短波 通信频率参数预测模型.

In the second part of the paper, the technology parameters of backward extrusion parts are optimized.

其次，论文对反挤压零件的工艺参数进行了优化。

Based on the optimized parameters, the backward extrusion and ironing formation technology experiment of shell parts is done.

接着，论文用优化的工艺参数对电池壳体零件的反挤压+变薄拉深成形工艺做了试验，归纳了反挤压和变薄拉深的模具设计要点和经验。

The choice of manufacture process parameters directly affects the quality and size precision of the workpiece.

成型工艺参数的选择对成型件质量的性能及精度有直接的影响.

Main kinetic parameters in anaerobic granular sludge fluidized bed ( AGSFB ) process and their determination were advanced.

介绍了厌氧颗粒污泥 流化床反应器 的主要动力学参数及其测定方法.

Using Wavelet Transform to detect the Glottal Closure Instant ( GCI), proposed pitch-synchronization and sample selection LP analysis based on the GCI information, the obtained parameters would be saved in the speech database.

利用小波变换检测语音信号的声门闭合时刻（GCI），利用语音信号的GCI进行基音同步和样本选择的多脉冲线性预测分析，将得到的语音参数保存到语音库中。

A typical mother board section GDX 11 was studied as an example to analyze the die configuration parameters and dimensions of large section.

本文以典型的、难度较大的底版型材GDX11为例，对大型模具的结构参数和尺寸设计进行了深入分析，并对模具材料及热处理与模具制造工艺和修模等进行了讨论。

Some Problem Concerned with Estimation of Parameters in GGM Model

秩亏GM模型参数估计的若干问题

It was shown that: ( 1) The different welding parameters have considerable effect on the microstructure homogeneity of welding seam and the HEZ as result of block ferrite in certain weldings by different heat inputs and cooling conditions.

结果表明，（1）不同的焊接工艺参数对焊缝和热影响区的组织均一性有较大影响。因为热输入及冷却条件的差异会使焊缝中形成粗大的块状铁素体；

Acquisition of 32-channel acoustic emission parameters: Design of field programmable gate array

32通道声发射特征参数的实时提取&现场可编程门阵列的设计

The paper introduces the technical parameters, compositions and principle of the test bench.

介绍了试验台的试验技术参数, 试验台的组成及原理.

The paper computes the gear parameters and optimizes the choices of differential gears by making use of the data management function and programs written in functions and commands of FoxPro.

利用数据库管理软件FoxPro的数据管理功能并利用其提供的函数和命令编写程序，进行齿轮参数计算和差动挂轮组优化选择。

With extended BASIC language programming, the regressive fitting computation is done in a Wang-2200 computer and a TRS-80 microcomputer, hence the model identification and the estimation of parameters are implemented.

回归拟合计算是在Wang2200计算机和TRS80微型机上用扩展BASIC语言编写程序，由此完成模型识别和参数估计。

One city power network~ s reliability parameters are calculated using a C program. Based on it, the whole system reliability is evaluated and lie weakest parts can be found and enhanced.

并以某市电网为例，采用C语言编写程序对其可靠性参数进行了一系列计算，以此评价整个系统的可靠性，并且找出网络的薄弱环节及最需要加强的部分。

The dynamic measurement and analysis of MSG-325 2-AXIS NC Diamond Tool Lathe manufactured by Rank Pneumo Inc. USA are presented in this paper and the modal parameters of the lathe are identified by means of real modal analysis method and complex model analysis method respectively.

本文针对美国Rank Pneumo公司生产的MSG-325型双轴数控金刚石车床进行动态测试与分析，并分别用实模态与复模态两种方法识别了该机床的模态参数。