parameters的例句大全

Using the LSX, many examples including the technique for feature parameters extraction, human body feature curve generation, scanned body reconstruction, body deformation, combination drive, and personalized human body modeling are given.

本文给出了从照片中提取用户人体轮廓和特征参数、用户人体特征曲线生成、三维扫描人体模型重建、混合驱动人体变形和个性化人体生成等的实例。

The selection of bath components and plating parameters was described in detail, fine greyish white electrodeposits were obtained which were analyzed by means of SEM and XPS with results that nickel-lanthanum-phosphorus alloy electrodeposits were obtained.

详细介绍了镀液各个组分及工艺条件的选择，获得灰白色、细致的合金镀层。对所得的镀层进行SEM观察和XPS分析，结果表明所得镀层为Ni－La－P合金。

Study on Car Door Stucture and Its Main Parameters for Urban LRV

城市轻轨车辆车门装置及主要参数的研究

According to the performance testing, the loading frequency, strain amplitude, lead diameter and durability were considered, the formula for parameters of LRD were derived.

通过对橡胶铅芯阻尼器进行性能试验，得到了加载频率、应变幅值和铅芯直径等因素对橡胶铅芯阻尼器性能的影响，对阻尼器的耐久性能进行了说明，推导了阻尼器各个参数的计算公式。

LMM and T of pathology parameters of tumor clinic were positive correlation.

胃癌淋巴结微转移（LMM）与肿瘤临床病理参数浸润（T）呈正相关。

The Calculation of the Property Parameters of Natural Gas Using LKP Equation

天然气物性的LKP方程求解

Thermokinetic Method Study for Kinetic Parameters Determination by LKB 2277 Bioactivity Monitor

LKB2277生物活性检测系统的热动力学方法研究

On the other hand, the experiments with the quenched 45 steel were done under different LFW parameters.

本文还对淬火45钢进行了LFW工艺试验。

Deducing the correlative parameters of heat and force in processing quadrate titanium alloy by LFW.

方型钛合金试件线性摩擦焊接过程中的热和力的相关参数推导。

Experimental Study on Basic Parameters for LFG Control and Utilization

LFG控制利用工程基本参数的试验研究

Field Trial of LFG Collection and Engineering Design Parameters

垃圾填埋气体收集现场试验与工程设计参数确定

( Following) the recommendatory parameters to get the best frequency response and noise immunity.

使用推荐的参数得到很好的频率响应特性和噪声抑制。

The paper introduces the basic structure and transmission principle of push rod rack drive and gives the formula and recommendatory value of the main parameters of the push rod rack drive, which provides a theoretical basis for its design and manufacture.

介绍了推杆齿条传动的的基本结构和传动原理，给出了推杆齿条传动主要参数的设计公式与推荐值，为该传动的设计及加工制造提供了理论依据。

According to the theory analysis, mathematical mode showing the lineal relationship between the response of airborne scanner and the effective reflected brightness of targets has been established under the reasonable assumption, exact physical significance for related parameters is given.

本文从理论分析出发，在合理的假设条件下确立了航空扫描仪响应值与地面有效反射亮度成线性的数学模式并给出有关参数的确切物理含义。

Dependence of optimized condition of KrF laser output on saturation parameters

KrF准分子激光的饱和参量与最佳激光输出

The binding constants KLB and distances r of these compounds and BSA were calculated respectively, according to Lineweaver-Burk equation and energy transfer theory. And every type of conjugation effort was estimated by the calculation of thermodynamic parameters.

以Lineweaver-Burk双倒数方程和能量传递原理分别计算了三者与BSA反应的结合常数（KLB）和结合距离（r）以及由热力学参数的计算判断了三种小分子物质与BSA结合的作用力类型；

The circuit parameters affecting the increase of peak pulse power of the device have been found.

找出了影响提高器件脉冲峰值功率的电路参数。

The experimental conditions and instrumental operation parameters such as KBH 4 concentration, flow rate of the carrier and shield gas, currents of lamp were optimized.

优化了光电管负高压，灯电流，屏蔽气和载气流量等实验条件。

Reynolds equation was calculated by use of JFO boundary condition in the numerical simulating research of the lubrication properties of crankshaft bearing, and the influences of some parameters on the lubrication properties of crankshaft bearing were analyzed.

将JFO边界条件引入曲柄滑动轴承的数值模拟计算过程，在成功求解Reynolds方程的基础上，选择一具体的内燃机曲柄滑动轴承进行了深入研究，探讨了若干因素对内燃机曲柄滑动轴承性能的影响。

For some representative uncertainty reasoning models, some concrete methods for selecting appropriate parameters during the uncertainty reasoning process based on lattice-valued first-order logics Jnf are proposed.

基于几类典型的不确定性推理模型，给出了基于格值一阶逻辑系统L（2nf）