parameters的例句大全

The Quantitative Calculation of Key Parameters of GFO Used in Edge Detection

GFO在边缘检测中的关键参数定量计算研究

The Empirical Computing Method of GFO Parameters in Edge Detection

广义模糊算子应用于图像边缘检测中参数的选择与经验计算

A new method for determining all parameters of GHM model is presented.

给出了确定粘弹性材料本构关系的GHM模型各参数的简便方法。

Some Problem Concerned with Estimation of Parameters in GGM Model

秩亏GM模型参数估计的若干问题

A typical mother board section GDX 11 was studied as an example to analyze the die configuration parameters and dimensions of large section.

本文以典型的、难度较大的底版型材GDX11为例，对大型模具的结构参数和尺寸设计进行了深入分析，并对模具材料及热处理与模具制造工艺和修模等进行了讨论。

Using Wavelet Transform to detect the Glottal Closure Instant ( GCI), proposed pitch-synchronization and sample selection LP analysis based on the GCI information, the obtained parameters would be saved in the speech database.

利用小波变换检测语音信号的声门闭合时刻（GCI），利用语音信号的GCI进行基音同步和样本选择的多脉冲线性预测分析，将得到的语音参数保存到语音库中。

Main kinetic parameters in anaerobic granular sludge fluidized bed ( AGSFB ) process and their determination were advanced.

介绍了厌氧颗粒污泥 流化床反应器 的主要动力学参数及其测定方法.

The choice of manufacture process parameters directly affects the quality and size precision of the workpiece.

成型工艺参数的选择对成型件质量的性能及精度有直接的影响.

Based on the optimized parameters, the backward extrusion and ironing formation technology experiment of shell parts is done.

接着，论文用优化的工艺参数对电池壳体零件的反挤压+变薄拉深成形工艺做了试验，归纳了反挤压和变薄拉深的模具设计要点和经验。

In the second part of the paper, the technology parameters of backward extrusion parts are optimized.

其次，论文对反挤压零件的工艺参数进行了优化。

This paper presents a prediction model of frequency parameters of short-wave communication based on-singleton fuzzy system.

提出一种利用非单点模糊系统建模的 短波 通信频率参数预测模型.

The effects of flunarizine ( FNZ) and/ or vitamin C ( Vit C) on the above parameters were observed.

进而观察盐酸氟桂嗪（FNZ）和／或维生素C（Vit C）对上述各指标的影响。

This paper analyzes and computes several FLR model, then use the best model to calculate the corresponding parameters.

同时，文中分析了几种场限环结构模型，对它们做出了数值分析，在得到了最佳模型后，计算相应的参数并制出相应的版图。

The surface shape of the workpiece is exactly modified by controlling the parameters of FJP, such as pressure, direction, working time etc.

通过控制液体喷射的压力、方向及驻留时间等量来定量修正被加工件面形的新型光学加工工艺。

Based on experiment, the influence of the process parameters of fluid Jet polishing ( FJP), including working pressure, working distance, jet angle and working time etc, on the removal rate of the workpiece is investigated.

以实验为基础，研究了液体喷射抛光技术的各工艺参数，包括喷射角、工作压力、工作距离和作用时间等参量对工件材料去除的影响。

The angle only data error is treated as mini disturbance of parameters and the sensitivity analysis model ( fhp) on nonlinear programming is established in the case without disturbance.

测角观测误差看作为参数的微摄动，而非线性规划的灵敏性分析模型（fhp）建立在无摄动的情况下。

The related key technologies of drill chuck's strength analysis were discussed and solved, such as the contact analysis parameters selection, the boundary conditions and the load processing, ANSYS command-string building and so on.

探讨和解决了钻夹头夹紧强度分析中夹爪与螺母接触分析参数的选择、约束边界和载荷处理、分析流程文件创建等关键技术问题。

This paper described the features and advantages of the mechanical and electrical integral product& FDZ □-12/ 630 vacuum automatic sectionalizer, and gave a general introduction of its technical parameters, structural features and working principle etc.

概述机电一体化产品FDZ口-12/630型真空自动分段器的特点和优越性，全面介绍其技术参数、结构特征、工作原理等。

Clinical efficacy ( daily emiction frequency, nocturia frequency, urgency and odynuria degree) and urine kinetic parameters ( FDV, MCC, Qmax) of the 2 groups before treatment, 1 month and 3 months after treatment were evaluated.

观察两组用药前、用药后1月、用药后3月的临床症状（每日排尿次数、夜尿次数、尿急和尿痛程度）和尿动力学参数（FDV、MCC、Qmax）。

Since 1987, some scientists in different countries have come to calculate the parameters of FCN by the observational data of gravity tide waves on the diurnal frequency band. They basically followed the Stacking Method, which needed five diurnal waves for the resolution.

1987年以来一些国家的学者相继开展了由潮汐资料解算FCN常数的研究，他们基本上都采用了5个周日波参与解算的迭积法（stacking method）。