radius的例句大全

Pin connected main frame, short turning radius, flexible mechanism.

铰接式车架, 转弯半径小, 机动灵活.

MANEUVERABILITY . Short turning radius . Rear engine, less weight on front.

灵活性:较小的转弯半径,发动机后置, 前部较轻重量.

HEAVY DUTY AUTOMOTIVE STEERING , with shorter turning radius.

重型自动方向盘:较小的转弯半径.

It used three-point suspension and tractors linked node, small turning radius units, with high productivity.

该机用三点悬挂装置与拖拉机挂结, 机组转弯半径小, 生产率高.

When the radius of the nanofiber after tapered region changes from large value to small value, the axile intensity of optical field transmitting in nanofiber increased firstly and then decreased gradually.

当拉锥后纳米光纤半径逐渐变小时，纳米光纤的光传输模场中心光强先逐渐增强然后又逐渐减小。

Radial velocity is bigger on axis top of tunnel at the distance of 3 times of radius to free face.

隧洞开挖的轴向洞顶距离掌子面3倍洞径处会出现一个爆破振速增大的区域。

By properly selecting initial value of calculating parameters, the shock wave propagation at the distance range out of 5 times of charge radius is accurately deduced.

适当选取起算参数，在5倍装药半径以外的爆炸远场范围计算精度良好。

Because of the continuity of the material, the elasticity property must be continuous in the transition area. Here we name the transition area as transition core and assume the stiffness varying linearly with the radius.

由于板材料的连续性，这个过渡区域必然是连续的，在这里，我们将这个过渡区域称为过渡核，并且，假设过渡区域的折算刚度是按半径线性规律变化的。

In Chengde area, water table is shallow, gravel bed is the main aquiferous layer and its penetrability coefficient is comparatively large, settlement radius caused by dewatering is large as well.

承德地区地下水位较浅，含水层主要为圆砾层，并且渗透系数较大，基坑降水引起的地面沉降半径也较大。

The change of SO2 partial pressure, O2 partial pressure, average porosity and average pore radius of product layer on unreacted core were discussed based on the model. The features of calcination in constant temperature were also discussed.

在本文所建立模型的基础上讨论了未反应核表面SO2、O2分压的变化，产物层平均孔径和平均孔隙率的变化，并且讨论了实验工况难以实现的恒温煅烧特性。

The unique reverse structure was also put forward. ( 2) The processes and methods of calculating wall-attachment radius, wall attachment distance varied with the offset ratio were derivated using Attachment Point Model and Control Volume Model respectively.

分别使用附壁点模型与控制面模型，推导出附壁半径，以及对应各种位差时的附壁距离的计算过程和方法。

When the radius or half of larger side is ten times larger than the free-space wavelength, attenuation rate is very low and hardly related to the shape of cross sections, and only related slightly to the area of cross section of tunnel.

当隧道半径或长边长的一半大于波长10倍以上时，电磁波的衰减率很小，几乎与横截面形状无关，仅仅与隧道横截面积的大小有微弱的关系。

The eccentricity and radius clearance were solved by the use of apposition of the above stated two equations.

利用上述两方程联立求解偏心率和半径间隙。

Objective To investigate the impact of dorsally angulated malunited distal radius fractures on the stability of the radiocarpal joint.

目的研究桡骨远端骨折背侧成角畸形对桡腕关节稳定性的影响。

Water Flow Behaviors of Channel Bend in Middle Sized Radius and Big Bend Angle of Curvature

中等半径大偏转角弯道的水流特性

Mathematical formulas are derived comprehensively and systematically for the profile coordinate, pressure angle and radius of curvature of the cylindrical cam with an oscillating roller follower.

推导了摆动滚子从动件圆柱凸轮廓线、压力角及廓线曲率半径方程，讨论了该种凸轮机构在各种运转情况下与之相适用的方程。

Nozzle flow field of SRM was numerically simulated with Fluent software. The effects of nozzle convergent half angle, radius of curvature on upstream of throat section and length of throat cylinder on flow field are investigated.

用Fluent计算流体力学软件对固体火箭发动机喷管流场进行了数值计算，研究了喷管收敛半角、喷管喉部上游圆弧曲率半径和喉部圆柱段长度对喷管流场的影响。

In this paper, the pressure angle and minimal radius of curvature of cam mechanism with swinging roller follower are discussed in details.

本文对摆动从动杆盘状凸轮机构的最大压力角和最小曲率半径问题进行了详细的讨论。

Focusing on the research of some important design parameters impacting the carrying capacity of the bearing, including radial clearance, contact angle and groove radius of curvature coefficient, a detailed analysis was given, and the corresponding bearing design recommendations were presented.

着重对影响轴承承载能力的重要设计参数径向游隙、接触角、沟曲率半径系数等进行了仿真，并给予了详细的分析，提出了对应的轴承设计建议。

In this paper, with the principle of high pair replaced by low pair, the cam mechanism is transformed to linkage, through the analysis of the linkage the equation of the pressure angle and the radius of curvature and profile of cam is established.

本文运用高副低代原理，将凸轮机构转化为低副机构，通过低副机构运动分析建立起凸轮廓线、曲率半径及压力角表达式。