set-point的例句大全

Open valve to balance set point as recorded in Step 9.1.

按照步骤9.1的记录将阀门开启到平衡设置点上.

It is not necessary to change the memory set point.

不需要改变记忆设置点.

The pressure set point is adjustable within the spring range.

压力设置点在弹簧作用范围内是可调节的.

The set point is determined by the adjustment of the spring force.

决胜点是坚决的被春天力量的调整.

Open valve to balance set point as recorded in 8.2.

将阀门开启到步骤8.2所记录的平衡设置点.

Or to set point of all or maybe to point where everything crosses Point of gravity?

还是指定地点?或者可能到所有建筑的交叉处?(重心)?

Turn the screw Clockwise ( IN ) to increase the set-point you are controlling.

顺时针方向旋转螺丝 ( IN ),上升正在控制的设置点.

Control with Fixed set Point of Load for Solvent Primary Tower.

PTH氨基酸的高效液体色谱分析——梯度溶剂的改进.

Turn the screw Counterclockwise ( OUT ) to decrease the set-point you are controlling.

逆时针方向旋转螺丝 ( OUT ),降低正在控制的设置点.

Open valve to balance set point as recorded.

将阀门开启到所记录的设置点上.

The full-graphics , backlit LCD simultaneously displays set point and actual fluid temperature.

高清晰有背光照明的液晶显示屏可以显示所设定的温度和流体的实际温度.

This article discusses the algorithm for the three-dimensional set point through the use of helix structure.

论述了运用螺旋结构构造三维点集的算法.

The thermostat activates the heater when the enclosure internal temperature drops below the set point.

当外壳内部温度下降到设置点以下时,温度调节装置启动加热器.

There are valve dither and valve set point circuit to improve the performance of the system.

为改善伺服阀的特性,在系统各通道的伺服输出电路中增加了可程控的阀偏置和阀颤振电路.

Note Set point for vibration switch is adjusted to maximum sensitivity during commissioning.

说明振动开关的设定值在调试时可以调整到最大灵敏度.

This paper, by using the strong resistance of Hough transform to noise and its characteristics of extracting points in the vicinity of different lines, studies the curve detection when x I, y I of the discrete data point set M satisfy the exponential function relation.

利用了霍夫变换抗噪声能力强和能分离出属于不同直线附近点的特性，研究离散数据点集M中xi，yi满足指数函数关系时的曲线检测问题。

Flash dance Great fun while dancing: Hold a small point-and-shoot, set to slow-sync flash thereachingthefloor.

用闪光灯拍摄舞蹈场面,有趣极了: 把相机的闪光模式打到“慢速同步”(前面说过这个名词啦).

PID theory decides the controller generally based on past information and set point of the output.

通常的PID控制,是根据过程当前的和过去的输出测量值与设定值的偏差来确定当前的控制输入.

The set point can only be maintained for one specific load condition.

设置点仅仅能在某一个负载的情况下实现.

Set up a stop loss point on the need to implement.

而设立了止损点就必须执行.