shaft的例句大全

Magnetic fluid sealing technology is a brand new sealing technology for rotating shaft dynamic seal by using amorphism of magnetic fluid and its response characteristics to magnetic field.

磁流体密封技术是利用磁流体形态的无定形性和它对磁场的响应特性将其应用于旋转轴动密封的一种全新的密封技术。

Experimental study on high strength composite shaft lining in deep alluvium

深厚表土层中高强复合井壁结构的试验研究

Progress and Prospect of Special Shaft Sinking Methods Through Alluvium in China

特殊凿井技术在我国的发展与前景

Conclusion Few traumata, no harm in periost and blood circulation, good apposition and alinement, quick healing and good recovery of functions are all the characteristics of this simple operation in treating fracture of humeral shaft.

结论本方法操作简单、损伤小、不破坏骨折端骨膜及血运，骨折对位、对线好，骨折愈合快，功能恢复好，是治疗肱骨干骨折的一种理想选择方法。

Quick-construction of Air Intake Shaft of Xinyuan Coal Mine

新元矿井进风立井井筒快速施工

This paper expounds the engineering conditions and geological conditions, construction methods and main mechanical equipment of the air intake shaft of Xinyuan Coal Mine, Shanxi Province, and introduces emphatically the construction technique, construction organization and management.

阐述了山西新元矿井进风立井的工程及地质概况、施工方法和主要机械设备，重点介绍了该工程井筒的施工技术及施工组织和管理。

The accuracy of measuring residual stress in spindle shaft by means of small spot x-ray

小光点X射线测定锭杆残余应力的测试精度研究

In accordance with the methods and experiences in the development of subsystem ( ACAP) of shaft parts CAPP for the airborne equipment industry, the paper details preparations, part descriptions, principles, user in-terfaces and trends.

结合开发航空机载设备行业轴类零件CAPP子系统（ACAP）的方法和经验，从开发准备，零件描述、基本原理、用户界面、发展趋势5个方面谈CAPP系统的开发。

By theoretical analysis and numerical analysis to two kinds of absorbing well system of absorbing well group and intensive absorbing well, intensive design idea of the new auxiliary shaft-420m pump room system design was determined.

通过对小井群和集约化吸水井两种泵房吸水井系统的理论分析与数值分析，确定了新副井-420m泵房吸水井系统的集约化设计指导思想。

This paper describes the distribution of surface hardened layer and analyses of the residual stress in the nodular graphite cast iron crank shaft with its Journal and arm corner hardened simultaneously by high frequency induction heating.

本文叙述了对球墨铸铁曲轴轴颈与园角部位同时高频淬火后获得的硬化层分布，以及硬化层中残余应力分析。

Analysis and Treatment of Oil Leakage at Flange Coupling Rotor Spider and Main Shaft of Unit

机组转子支架与主轴联轴法兰处漏油分析及处理

Site Repairing Method for Type 300 Diesel Engine after Burning out of Crank shaft Bearing Liner

300型柴油机曲轴烧瓦后的现场修复方法

Finding involved inadequate corrective actions to prevent repeat failure of the number nine main crank shaft bearing on emergency diesel generator number one.

发现物涉及到不充分的，纠正措施，用来避免重复的失效，那是关于，9号大曲柄轴，在第一号柴油机。

Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft.

转动雨刷模组盖，并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。

With the third steps and the fourth steps natural frequency vibration, the smaller close to the second crank arm of crankshaft and round place natural frequency of the main shaft transition the position is.

以第3阶和第4阶固有频率振动，位置越靠近曲轴第二个曲柄臂与主轴过渡圆处固有频率越小。

Optimized of parameters of basic dimensions of double crank shaft mechanism

双曲柄机构基本尺寸参数的优化

A low cost microcomputer closed loop control system of crank shaft processing

经济型微机闭环曲轴加工控制系统的研制

Experiential Communion about Catching Dust Treatment of Foundry Cupola Exhaust Gas Application of Bag Dedusting Deal with Flue Gases in Mechanized Shaft Kiln

铸造业冲天炉废气除尘治理的有关经验交流袋式除尘新技术在机立窑烟尘治理中的应用

Vertical shaft impact crusher is used in fine crushing of medium and hard materials.

立式冲击破碎机用于中硬物料的细碎加工。

The Author analyzes the reason for the main shaft breaking witch is the most important part in PXQ1200/ 150A light hydraulic gyratory crusher by actual observation and theoretical analysis.

从实际观察与理论分析两个方面入手，对PXQ1200/150A轻型液压旋回破碎机最重要的部件&主轴的断裂进行分析。