shear的例句大全

The Role and Microstructure of Adiabatic Shear Band on a Steel Tube Ballistically Loaded by Explosive

钢管爆炸条件下绝热剪切带的作用和精细结构

The role of adiabatic shear bands within fragments of tubular steel ballistically loaded by explosive is investigated.

研究钢管在爆炸加载条件下绝热剪切带的作用。

In this paper, an improved shell theory is employed to analyze the free vibrations of a spherically isotropic spherical shell submerged in a compressible fluid medium. The effects of shear deformation, rotary inertia and transverse normal strain are included.

采用六模态的中厚壳理论研究了可压缩流体中球面各向同性球壳的自由振动，即在分析中考虑了剪切变形，旋转惯量和横向正应变的影响。

Experimental study on seismic behavior of shear walls wih X-shaped concealed bracing and concealed vertical joint

带X形暗支撑设暗竖缝剪力墙抗震性能试验研究

The effect of semi-rigid base layer conditioning period, high penetration emulsified asphalt spread temperature and conditioning temperature to the penetration effect were also analyzed. Furthermore, the shear strength test between surface and base layers were utilized to obtain the optimal content of high penetration emulsified asphalt.

并分析了基层养生龄期、高渗透乳化沥青洒布温度、养生温度等因素对渗透效果的影响。其次，进行了基层与面层间抗剪强度试验，得到了高渗透乳化沥青最佳用量。

The new shear connector of the bend bar on the one hand meets the requirements for shearing and lifting resistance, and on the other hand saves the construction time, labor and materials, and is of great vistas of popularization.

波形弯筋连接件既能达到抗剪切、抗掀起要求，又能省时、省力、省材，具有极大的推广应用前景。

The mixing process mainly involves the three following microscopic mechanism: fast convective mixing, slow diffusive mixing, and local shear mixing.

研究发现，床内物料混合过程大致可归纳为快速对流混合、缓慢扩散混合、局部剪切混合三种微观机理。

The velocity distributing, variation of extension rate, shear rate and the natural convergence angle of the fluid were analyzed under different initial entry pressure.

分析了在不同口模压力（P）下入口区速度分布、延伸应变速率、剪切应变速率以及流体自然收敛角的变化。

The shear strength of matrix layer in rolled compact concrete ( RCC) provides important effect to the safety of RCC dam.

碾压混凝土（RCC）层面抗剪强度关系到碾压混凝土坝的安全。

The Failure Stress Condition on the Maximum Cyclic Shear Surface Associated with the Failure Stain Criterion of Flyash

粉煤灰最大往返剪切作用面上应变破坏标准的应力条件

Through a series of dynamic triaxial tests, the failure stress condition on the maximum cyclic shear surface was discussed.

通过一系列的动三轴试验，探讨以应变为破坏标准的最大往返剪切作用面上的破坏应力条件。

It is justified that the maximum cyclic shear effect plane of the specimens in triaxial liquefaction test and-simple shea'r liquefaction test and of soil elements under general plane strain condition can only be determined by static stress components and is undependent on cyclic stress.

对于三轴液化试验、简切液化试验的受力条件和平面应变状态下土单元的受力条件，证明了最大往返剪切作用面的位置只由静力有效应力分量来确定而与往返应力无关。

The experimental results proved that ( 1) there is an additional cyclic strain hardening effect caused by non-proportional loading, and ( 2) the relative orientation between maximum shear plane and free surface plays significant role on fatigue life.

非比例加载引起的附加循环硬化；（2）最大剪切平面与自由表面相对取向对疲劳寿命的影响；

The mid-scale shear, strong frontal zone, Mongolia cyclone and surface cold front were main influence systems of forming sand and dust storm.

中尺度切变线、强锋区、蒙古气旋和地面冷锋是引发沙尘暴的主要影响系统；

Results show as follows. The heavy rain taking place in the west side of Dabie Mountain is caused by β-scale cyclone on α-scale shear, and the heavy rain near the boundary area between Hunan and Hubei provinces is caused by cyclonic wind perturbation.

结果表明：（1）大别山西侧的暴雨由中α尺度切变线上中β尺度低涡造成，湘鄂交界地带的暴雨由切变线上气旋性扰动造成。

Then the shear bearing capacity of corroded RC deep beams without stirrups is calculated on the basis of a combined resistance of beam action and arch action; and then the formula of the load capacity of corroded RC deep beams without stirrups is suggested.

再在梁-拱共同作用抵抗剪力的机制上，计算了无腹筋锈蚀钢筋混凝土深梁的抗剪承载力，进而提出了无腹筋锈蚀钢筋混凝土深梁的承载力计算公式。

Function and Characteristic of Tie Beam in Seismic Shear Wall

抗震剪力墙小跨高比洞口连梁的作用及特点

Tie beam is an important element in frame-shear wall structure.

连梁在框架-剪力墙结构中，也是很重要的一个构件。

The paper analyes interation shear , fluid forming process , and discuss the ore forming mechanism.

并在此前提下提出了构造-流体-岩石相互作用的金成矿机理.

The paper proposes a new method for calculating shear plane area based upon a new oblique cutting model with double edge.

根据新的斜角非自由切削模型，本文提出了新的剪切面积计算方法。