shrinkage的例句大全

The holes of anchor bolts will be grouted with normal ( Portland, non-shrinkage ) cement mortar.

这些地脚螺孔将灌入普通 ( 波特兰, 无收缩 ) 水泥砂浆.

The shrinkage hole in the casting can be effectively eliminated by using the cross gating system.

通过采用十字型横浇道,避免了铸件缩孔的产生.

After eating turtle hibernation, brain shrinkage in the shell.

乌龟冬眠之后就不吃不喝, 脑袋缩在壳里.

When the low water-cement ratio gets off, concrete self-desiccation shrinkage produces easily.

低水灰比下, 混凝土的自缩现象很容易发生,从而加大了混凝土开裂的可能性.

Shrinkage stress was found to increase linearly with cure temperature.

我们发现收缩应力随固化温度直线增加.

Hygro-instability: Stretch or shrinkage of paper due to moisture content.

水份不稳定性: 纸张含水量不稳定引致伸长或收缩情况.

The swelling or shrinkage with changes in moisture content is known as movement.

木材随含水量变化发生膨胀或收缩,这种现象称为胀缩.

The resulting economic shrinkage is leaving large swathes of property in negative equity.

随之而来的经济萎缩,使大量房地产都变成了负资产.

The effects of oligomer and diluent on the shrinkage of curing system were discussed.

讨论了齐聚物及稀释剂对固化体系收缩率的影响.

Introducing the example, volume and shrinkage rate of persimmon were calculated.

并通过实例, 对柿子干制时的体积收缩率和表面积收缩率进行了计算.

Shrinkage is the retail trade's euphemism for shoplifting.

商品损失(Shrinkage)是零售业对有人在店内行窃的委婉说辞.

Consistency of Shrinkage-reducing Agent and Water Reducing Agent.

减缩剂和减水剂的相容性问题.

Durable , white, water-resistant, low shrinkage resin for stereo lithography for SLA system.

应用于立体光刻技术的耐久性, 白色, 防水和低收缩的树脂.

Shockproof additive is added order to restrict the shrinkage at temperature and the formation of crazing.

加入防缩剂,防止衬体在高温下因烧结而产生收缩,导致龟裂的现象.

Shrinkage and creep are the inherent time-dependent characters of concrete which belongs to a viscoelastic material.

混凝土收缩和徐变是粘弹性材料的一种固有时变特性.

The process conditions and points to controll elasticity, width and weft shrinkage were presented.

文中给出了染整加工中的工艺条件,指出了在整个加工过程中控制弹力 、 门幅及纬向缩水的注意事项.

Used for drying all kinds of textiles after shrinkage test.

用于各类纺织品经缩水试验后的干燥.

Penpoint fracture and breaking on the early course of drawing are caused by shrinkage void inside the rod;

断口呈笔尖状，在拉拔早期发生断裂是由于内部存在缩孔缺陷所致；

During the manufacturing process a plant usually experiences a degree of material shrinkage.

在生产过程中,工厂通常总要受到一点材料上的损失.

The MC grade, shrinkage and wood surface stress during drying progress was the largest in consecution heating, and was least in fluctuating-heats ( 6h). The effect of heating methods on dry quantity of small-diameter lumbers was significant.

干燥过程中锯材的含水率梯度、表层应力和干缩量均以连续加热干燥试验最大，波动2时干燥试验次之，波动6时干燥试验最小。