wheel的例句大全

Without ABS a driver can get maximum braking effort by braking to the point of wheel lock, and then reducing the pressure ever so slightly to the point where the wheels are rotating again.

记住轮胎处于接近锁死状态时刹车效率最高，在没有ABS时，车手可以刹到刚刚锁死的临界点来达到最大的刹车效果，然后微微减少刹车力度让轮胎恢复转动。

In conclusion, we know after the front suspension optimized, the front wheel alignment parameters is more reasonable. The variation of tread is minished so that the abrasion of the tire is reduced. And also the vehcile keep some understeering characteristic after front suspension optimized.

最后总结出优化之后的前悬架使得前轮的定位参数更加合理，减小了轮距变化量，从而降低了轮胎磨损，并保证了样车具有一定的不足转向特性。

The analysis results showed that the instantaneous oversteering or understeering of the vehicle can be reduced by the control of the rear-wheel steering angle to enhance the dynamic steering stability.

分析结果表明，能够通过控制车辆后轮转向角来减小汽车瞬时出现的过多转向或不足转向，增强了汽车的动态转向稳定性。

Previously, workers had pushed the coal to a nearby river by wheel barrow.

而在火车建成前，工人们要通过独轮车将煤炭运到附近的河流里。

The dental abrasive testing machine applies a V-like swing arm to driving the wearing part to move along the slope back and forth, which is connected with an eccentric wheel fixed on the crankshaft of the gear motor through a connecting rod.

该机采用V形摆动臂来驱动磨耗部分沿斜面作往复磨耗运动，V形摆动臂通过连接杆与减速电机轴上的偏心轮连接。

Power cut-off device in brake system of wheel loader

轮式装载机制动系统动力切断装置

The power cut-off device in wheel loader can combine the three braking conditions of service brake, emergency brake and parking brake, can disconnect the power quickly and effectively under whatever situation to ensure reliable brake operation.

轮式装载机动力切断装置可将行车制动、紧急制动、停车制动三种制动工况结合起来，在任一种工况下均能快速有效地切断动力，使制动效能可靠。

Development of Object-oriented CAD System for Disk Cutter of Sprocket Wheel

面向对象的盘形链轮铣刀CAD系统的开发

Distinguishing Wearing Capacity of the Wheel Tread Contour of Locomotives and Cars

火车车轮踏面磨损量识别研究

Principal axis connected with knob is available in shell, whose upper and lower section is respectively configured with synchronous upper and lower concave wheel and shifting fork.

在外壳内，设与旋钮相连的主轴，其上下段分别装同步的上、下凹轮和上、下拨叉；

Worn clutch facing disc wheel for steel wire needle sharpening

磨损的离合器摩擦片磨钢丝针用薄片砂轮

Hard Roll Facing Technology of Mg Alloy Wheel

镁合金机轮滚压强化工艺

To the structure of the internal market as the standard, can be divided into wheel axis, multi-core type, mesh type, mixed type and intangible so five large factory-type model.

以内部市场结构为标准，可划分为轴轮式、多核式、网状式、混合式和无形大工厂式等五种模式。形成区域特色产业集群，是实现苏北新型工业化又好又快发展的必要选择。

Combining yarn weight deviation and drawing frame weight deviation to adjust wheel gear, valid control weight deviation per hundred meter yarn and weight CV% was achieved.

兼顾成纱重量偏差和末并单机台重量偏差来调整末并牵伸齿轮，达到有效控制成纱百米重量偏差和重量CV%的目的。

Balancing Weight to Turbo Wheel Blades Without Dynamic Balancing

无需动平衡的叶片配重

The paper introduces the preparation equipment of coarse DIP, including bale wire cutter, braker, leveling wheel, radiometric scale, drum pulper and combined sorter.

本文对脱墨用粗浆的制备设备作了简要的介绍，包括剪铁线机、散包机、匀纸辊、称重装置、碎浆机及复合筛。

Apply the industrial control technology, field bus technology and robotics technology to the large scaled balk cargo delivery equip ment ── bucket wheel stacker reclaimer.

将工业控制技术、现场总线技术、机器人技术应用于大型散料输送装备&斗轮堆取料机的控制系统。

Now we also produce Wheel Barrow, Tool Cart, Service Cart, Hand Trolley and their parts and components.

同时我们还生产手推车、工具车、服务车、货仓车及其零部件。

When Chapeyama collapsed last week from the same disease, a friend took her in a wheel barrow to the nearest clinic where she died a few hours later.

当Chapeyama上周同样由于霍乱病倒时，一个朋友用手推车将她带到最近的诊所，几个小时后，她就去世了。

This paper describes the methods of computer aided modeling and numeral control machining to be used in design and manufacture of high precision solid casting dies, which contributes to the nationalization of the fan dynamic bladed wheel for a certain product.

论述在设计制造高精度的整体叶轮压铸模的过程中，采用的计算机辅助造型和数控加工的工艺方法，成功的实现了某产品叶轮制造的国产化。