wire的例句大全

In computer security, an intruder detector aa matrix of foil or fine wire.

在计算机安全学中, 一种入侵者检测器.

Copper is easily shaped into thin sheet or fine wire.

铜易于塑成薄板或细丝.

The interface on the data wire may affect the transfer speed of data directly.

数据线上接口会影响数据的传输速度,用英语怎么说?

The quantity of heat is related to working voltage, the length of core wire and cable.

JMI加热电缆发热量与工作电压 、 发热芯线和电缆长度有关.

Remove the cable core wire at pedal arm.

拆下踏板臂的电缆芯线.

Ceramic core wire wound construction.

陶瓷核心绕线结构.

Remove coil wire from distributor and secure to good ground to prevent engine from starting.

从分电盘上拆下线圈电线,同接地线路接牢,以免引擎启动.

Collectoris connected to the coil wire of the motor.

收藏家被连接到马达的卷导线.

The practice shows that the design of bolt wire mesh is reasonable and practicable.

实践结果表明,锚网支护设计方案合理可行.

Multi types and sizes of bead wire with high tensile strength should be developed.

胎圈钢丝要发展多品种、多规格和高强度产品.

Stay from bare wire, please.

请勿靠近裸露的电线.

Disconnect and isolate the battery negative cablUnplug the 2-way heated seat back wire harness connector.

断开并且绝缘电池负极电缆.拆下2路加热座椅垫线束接头.

At last , the author brings forward some suggestions about Beijing's axle wire design . "

并对北京 中轴线 的城市规划提出了一些建议.

The composition and working principle of an underwater wire saw tensile force detecting system was introduced.

介绍了水下绳锯机串珠绳张力检测装置组成和工作原理.

Free abrasive wire saw technique is the main method for monocrystalline silicon slicing process.

游离磨料线锯切割技术是目前单晶硅切片的主要加工方法.

( anatomy) of or relating to the tarsal bones. Percutaneous Kirschner wire intramedullary fixation of the shaft and neck fractures of the second to fourth metatarsus

（解剖学）属于或关于跗骨。经皮克氏针治疗第2、3、4跖骨干、跖骨颈骨折

DN3 series spot welder is widely utilized in the spot welding of mild steel, corrosion resistant plate and round wire in the industries such as panel beating, light fittings and hardware appliances.

系列点焊机同样广泛应用于钣金，灯具，五金电器行业中低碳钢、不锈钢板和圆丝的点焊。

A metal weight at the end of a sounding line. Bend the end of the wire back.

在探深索的尾端的金属球。将这根金属线的末端向后挠曲。

The procedure parameters to keep smooth bead on both sides with single side welding for the sheet, groove size of backing, assembly gap, traverse tolerance between wire and workpiece are all determined by experiment.

通过工艺试验，确定了保证薄板单面焊双面成形、光滑均匀的工艺参数范围、背面垫板凹槽尺寸、工件装配间隙、焊丝和工件的横向偏差量等。

In combination with a linear wire wound potentiometer and a cam-actuated angle displacement sensor, a hydro-electric proportional relief valve is used as pressure controlling element of hoist system to compose an open loop control system for overload protection.

采用电液比例溢流阀作吊机系统压力控制元件，与线性线绕式电位器和凸轮构成的角位移传感器一起组成吊机过载保护开环控制系统。