zone的例句大全

After completion and operation of the TGP, the water-sand conditions of the Yangtze River will be changed and sedimentation will occur in the backwater zone at the tail of the reservoir.

三峡工程投运后，改变了长江的水沙条件，引起库尾变动回水区泥沙淤积；

The landslide early warning could base on the study on lag characteristic and rainfall threshold, by the use of rainfall information. ( 5) The backwater amount in unsaturated zone in landslide was estimated.

通过潜水位对降雨的滞后响应特征以及降雨阈值的分析，提出利用降雨信息对滑坡进行提前预警；（5）对滑体中非饱和带滞水量进行了估算。

The impressed depression caused by block adjusts the mesoscale pressure field, the dense barometric gradient zone distribute in North Fujian and North Taiwan Strait and caused the wind stronger in these area.

其中由于阻挡作用产生的地形诱生低压效应，使得在中尺度上气压场产生调整，气压梯度密集区集中在福建北部和台湾海峡北部海区，造成这一带海区大风偏大其他海区。

By changing the thickness of organic and inorganic layers or adjusting the relative height of barrier potential at organic-inorganic interface, we can control the emission zone and obtain different emission from each layer.

对所制备的3种结构器件的EL进行了比较，研究了结构对发光起因的影响，揭示通过调节有机层和无机层厚度以及界面势垒高度可以实现对发光区域的控制。

After reformation of drill pump, rotary table and drilling rod, the triple-men portable rig has achieved good results when drilling is in breed zone by netting box and other land areas.

对三人钻机的压水泵、转盘、钻杆部件进行改进后，三人钻机在围网养殖区以及其它陆上钻井时，都取得了良好的效果。

Drilling holes in the distal phalanx near to backside of basilar part for repair of extensor tendon Zone ⅰ avulsion of finger in the stop point

远节指骨靠近基底部背侧钻孔修复指伸肌腱Ⅰ区止点处撕脱伤

Investigation on the chiral recognition site of enantioselective separation of ofloxacin by capillary zone electrophoresis using vancomycin as a chiral selector

毛细管电泳中万古霉素拆分氧氟沙星对映体手性识别位点的探讨

Three main decollement surfaces ( or zones) and low-strong deformation zone, middle folding layers and upper bedding slip slabs have been demonstrated in the Nanhua area of the northwest part of Hubei province.

鄂西北南化塘一带已确定出滑脱构造由三个主滑脱面（带）与下部强变形带、中部褶皱层及上部层滑岩片构成。

At first, utilized ANSYS to analyze the anchorage zone on the cable bent tower and investigate stress distribution and deformation at the area.

首先利用ANSYS软件针对索塔锚固区所选节段进行了详尽的空间有限元分析，考察索塔锚固区的应力分布和变形情况。

Anything at or just below the surface of the seabed the benthic zone, in fishery parlance gets dragged up.

海底或仅仅在海底表面下一点，用渔业的说法，就是深海底栖带，任何生活在这里的生物都会被拖上来。

Preliminary investigation on benthic ecology in intertidal zone of Haitan Island

海坛岛潮间带底栖生态的初步调查

The study on the ecology of the benthic community in intertidal zone, Fujian islands

福建海岛潮间带底栖生物群落生态的研究

A study of the benthic algae in intertidal zone of islands round the east of Shandong Peninsula

山东半岛东部海域诸岛潮间带底栖海藻的研究

This paper illustrated ecological situation of intertidal zone sediment by size, sorting coefficient and the structure of benthic community.

本文从潮间带沉积物的粒径、分选系数及底栖生物群落结构阐明潮间带生态现状。

Studies on the benthic fauna community structure of the intertidal zone of rocky shore in Zhoushan waters

舟山岩相潮间带动物群落结构的研究

Studies on intertidal zone ecology of the benthic fauna in Xiangshan Harbor and Sanmen Bay ──ⅲ. community structure

象山港、三门湾潮间带生态学研究&Ⅲ.群落结构

Zone Characteristics of Chinese Mountain Torrent Disasters and Countermeasures

中国山洪灾害区域特征及防治对策

Based on practical data about rock block mountain, rolling loess land ( pluvial tableland), flat loess land ( pluvial fan skirt) and terrace, the relation between geomorphological structure in the Weihe basin zone and active faults and neotectonic movement is studied.

根据基岩断块山地、波状黄土塬（洪积台地）、平缓黄土塬（洪积扇裙）、阶地等较多实际资料，研究渭河盆地带地貌结构与活动断裂及新构造运动间的关系。

Then the bidding rules based on the capacity and the adjustment of generation are presented, Furthermore, a method of congestion management, combined with the prize zone and the spot price, is introduced to be suited to the multi layer power market in future in China.

设计了基于容量报价和调整报价两种实时报价方法，给出了将区域电价和实时电价相结合的阻塞管理方法以适应我国未来的多级电力市场模式。

With the increase of the extrusion speed, billet temperature and die temperature was gradually increased. The highest temperature was located in bearing export while the flow dead zone located in diversion hole of die and the stress of bearing have sharp risen.

随着挤压速度的增加，坯料的温度和模具的温度逐渐上升，温度最高的地方在出口工作带上，模具的导流孔的圆角部分存在流动死区，工作带的应力急剧升高。