仿真的例句大全

Hopf bifurcation from synchronous chaos and its circuit simulation in a coupled nonlinear oscillator system

一类耦合非线性振子同步混沌Hopf分岔及其电路仿真

Car Simulation Analysis and Experimental Study Based on Rigid-flexible Coupling Model

基于刚柔耦合模型的轿车仿真分析及试验研究

Simulation of covariance analysis describing equation technique for terminal weapon delivery

协方差分析描述函数法在终端航空武器投放动态仿真研究中的应用

A Simulation Study of Controlled Coyote Blast with Column and Strip-shaped Charge and Its Application in Highway Subgrade

条形药包硐室控制爆破仿真研究及其在高等级路基工程中的应用

Fluid catalytic cracking process dynamic model and simulation ──ⅰ. process dynamic model

催化裂化过程动态模型及仿真&Ⅰ.过程动态模型

Real Time Simulation and Wave Spectrum Analysis for Random Sea Wave of Long-crested Wave

长峰波随机海浪的实时仿真和频谱分析

It mainly studies on the power dissipative Crowbar circuit on the dc side. The validity and correctness of the control is confirmed through the Matlab/ Simulink simulation.

重点研究了直流侧耗能Crowbar电路的低电压穿越策略，并对其仿真研究，结果验证了其有效性和正确性。

Influence of the Earth Curvature in the Airborne Radar's Function Simulation

机载雷达功能仿真中地球曲率的影响

Based on the simulation, the earth curvature's influence to target echo and surface clutter power was analyzed quantitatively.

在仿真实验的基础上，分析了地球曲率对目标回波和面杂波功率的影响。

Theoretical calculation shows that the sun phase angle, observation distance and the brightness magnitude of the targeted satellite change significantly because of no earth curvature effect and large separation distance in position.

仿真计算表明，天基观测由于不受地球曲率影响，且观测几何拉开，太阳相位角、观测距离变化范围较大，因此目标卫星视星等变化范围较大。

Study of straight and curved surface intersection principle, generating root cleaning cutter locus of points. 2.

研究直线与曲面求交原理，生成清根刀心点的轨迹。2.后置处理与加工仿真。

The results of simulation showed that this signal can excite CUT efficiently, and accuracy of classification of wavelet SVM was good.

仿真结果表明，该激励条件下，利用小波-支持向量机能够较好地对模拟电路进行故障诊断。

Finally, the PSPICE simulation shows the tunable characteristic of cut-off frequency.

最后利用PSPICE工具进行仿真，实验结果表明具有截止频率可调的特性。

This paper analyzes the failure mechanism of gears, cooperates dynamics and FEM to calculate fatigue life of gears, then predicts residual fatigue life of third speed gears of transmission case based on known damage history.

本文分析了齿轮的失效机理，运用动力学和有限元联合仿真法来计算齿轮总的疲劳寿命，结合齿轮的服役历史对变速箱三挡啮合齿轮的剩余疲劳寿命进行了预测，并给出了预测模型。

It was found out as far as the maximum channel delay is less than the cyclic prefix, the effect of timing synchronization errors i.e. ISI is drastically reduced.

仿真结果表明，只要最大信道延时小于循环前缀的长度，定时同步错误所引起的码间干扰将大幅降低。

Analysis and Simulation of Flow Characteristics of Cycloidal Pump

摆线泵流量特性分析及计算机仿真

Multi-Objective and Varying Parameter Optimization of Machining Parameters Based on NC Simulation Data

基于仿真数据的数控铣削加工多目标变参数优化

By means of the model, the dynamic characteristics of marine nuclear steam turbine plant under the rapidly varying duty working conditions is calculated and analyzed.

利用该仿真模型对快速变负荷工况下船用核汽轮机装置的动态特性进行了计算分析。

The result indicates that the model can simulate the varying duty working characteristics of nuclear steam turbine plant accurately, and meets the needs of simulation analysis work on secondary system of nuclear power plant.

结果表明，该模型能准确模拟核汽轮机装置的变负荷运行特性，满足核动力二回路系统实时仿真分析要求。

Walsh function approach to optimal control and Simulation of linear time-varying system

用WALSH函数实现线性时变系统的最优控制和仿真