几何的例句大全

Therefore, study several with the vector algebra knowledge the problem is in clear and ordered pattern.

因此, 用向量代数知识钻研几何问题是顺理成章的.

Because studies the geometry question with the vector algebra knowledge is logical.

因此,用向量代数知识研究几何问题是顺理成章的.

The teaching of plane analytical geometry is short of the suitable courseware resources in practice.

适合学校实际平面解析几何课堂教学的课件资源匮乏.

Based on the principles of space analytical geometry, methods for computing the coordinates of the center of cutting disc, its angle of depression and elevation, angle of lateral swing and angle of twist are derived.

根据空间解析几何原理，推导出盾构机刀盘中心三维坐标以及俯仰角、横摆角、扭转角的计算方法。

Geometry Model for the Single Helicoidal Pump ( Auger Stem) and Its Manufacture

单螺杆泵（钻具）几何模型及其制造问题

There is no royal road to geometry.

几何无坦途.

China University of Geosciences Information Engineering College on the geometry transform some of the material.

中国地质大学信息工程学院的关于几何变换的一些材料.

The technique of NURBS applied widely in CAD was adopted to the modeling of free surface shell, and then get two type of initial architectural project of free surface shell with the platform of UG.

并突破了传统的建筑领域内欧氏几何造型的限制，在UG平台下完成了以现代建筑方案设计为目标的自由曲面薄壳屋面实例造型。

The system includes geometry processing module, manufacturing technology module and subroutine program library.

该系统由几何处理模块、工艺处理模块、后置处理模块和子程序库组成。

We create an obstacle with a small table and four chairs, on the next figure you can see the geometry inside the circle.

在你能见到里面几何学圆周下一个大小上，我们以一张小桌子和四张椅子产生一个障碍。

The influence of knife-edge outline on the spot measurement is discussed and somearein this paper.

本文从理论上分析了刀口的几何特性与物理特性对微小光斑测量的影响.

Adult hair arsenic data were positive skewness distribution, and calculating average should use geometric mean or median;

成人发砷值呈正偏态分布，在计算平均值时应当使用几何均数或中位数；

Time is money, just figure out how much?

时间即金钱，光阴价几何？

and the radial central line of each supporting block lags behind the geometric central line of the corresponding thrust bearing pads.

每个支撑块的径向中心线滞后相应推力轴瓦的几何中心线。

The allowable stress number, load, geometry parameters and life have the most significant effects on pitting resistance rating results;

试验齿轮的应力修正系数、载荷和几何参数对弯曲强度计算结果的影响较大。

A unified formula of Vandermonde identities and some hypergeometric transformations

Vandermonde卷积公式统一形式及其相应超几何变换

They are mainly used to process or sculpt the metallic products'picture size and graphics context.

主要用于各种金属制品表面图文、几何形状尺寸精密加工或镂空.

We use the Finite-difference Time-domain ( FDTD) method to compute the scattered field of an object possessing several scattering centers. The numerical diffraction coefficient of the scattering center under investigation is then obtained by solving simultaneous equations established via GTD consideration.

利用时域有限差分（FDTD）法提供的散射场，根据几何绕射理论（GTD）建立含有绕射系数未知量的方程组，通过联立方程组的求解，得到散射体边缘的数值绕射系数。

Applications of tessellation in contemporary architectural surface design

镶嵌几何在当代建筑表皮设计中的应用

Quality Control of Spatial Data Geometric Accuracy: Status and Future

空间数据几何精度的质量控制研究现状与未来研究重点