孔的例句大全

The effect of proportional overload on the low cycle tension-tension fatigue life of aluminium alloy plate with circular hole

比例超载对铝合金圆孔薄板试件低周拉-拉疲劳寿命的影响

The results showed that the hole had a great impact on the rigidity of aluminium alloy plate, and there was a critical length of composite material patch.

结果表明：开孔损伤对铝合金板的平均刚度有很大的影响，且修补所用复合材料补片存在临界长度。

Effect of La content on growth of voids along interface between aluminized coating and steel substrate

炎性渗出物集合在表面。La含量对渗铝层/基体界面孔洞生长的影响

Each of the mature pollen grains has 2 nuclei, 1 germination pore, Its ovule is anatropous, double integument and tenuinucellate.

成熟花粉粒2核，1萌发孔；

The research shows that when cone angle is less than some value, its increase will decrease the deformation of an anchor and raise its field load greatly, and for a mono-strand anchor, reasonable cone angle varies from 6.5 ° to 7.5 °.

研究表明，当锥角小于某值时，较大的锥角能明显减小锚具变形；对于单孔锚具，合理的锥角介于6.5°～7.5°之间。

Simplified Calculation for Retaining Pile and Anchor Pile in Hand Drilling

人工挖孔挡土桩锚桩的简化计算

According to actual test result based on anchorage granulated substance body compactness and the anchor span friction distributed regularity obtained by using the stress measuring technique, a more thorough understanding of the anchorage anchor mechanism has been acuired.

根据有关基于内锚头砂体密实度的实际测试结果，以及采用应力测量方法得到的锚孔摩阻力的分布规律性，对砂固结内锚头的锚固机理有了更深入的认识。

Effects of 45 ° Chamfer Angle and Fillet on Shrinkage Porosity ( hole) in Investment Castings

45°倒角与圆角对熔模铸件缩松（孔）的影响

It is presented that the differential pressure orifice flowmeter and the angle joint differential pressure measuring structure used in the test are the applied technologies of H2O2/ kerosene engine test.

提出了压差式孔板流量测量和角接式取压结构在过氧化氢/煤油发动机试验中的应用技术。

Comparing with other ancient architectural complex, the most distinctive point of Qufu Confucian Temple is its long history and vitality.

与其他古建筑群相比，曲阜孔庙最与众不同的一点在于其悠久的历史与生命力。

In terms of geometry, the defining parameters are the body width, hole diameter and the location of the applied load.

在条款几何，确定参数是身体的宽度项，孔直径和地点应用负载性。

An approximate analysis of net section normal stress in a laminate strip with a circular hole

含孔层压板条净截面正应力的近似分析

Aquaporin and Water Transport in Plant

水孔蛋白与植物的水分运输

The razor processing of the inner hole outer circle and the end face of the work piece can be carried out simultaneously only requiring a cutting tool and two arbors.

只需用一把刀具、二把刀杆就可同时进行工件的内孔外圆和端面的精剃加工。

Study on arc light sensing of keyhole behavior in plasma arc welding of stainless steel

不锈钢等离子弧焊熔池小孔行为的弧光传感研究

Study on front side arc light sensing in keyhole. mode plasma arc welding

穿孔等离子弧焊正面弧光传感技术研究

Grazing the right-bank dike and aiming carefully for the middle arch of the stone bndge below;

顺流而下，擦过堤岸的右侧边缘，小心地对准下游石桥的中孔滑下。

In the design of linear accelerating structure, the coupling factor between cavities is a crucial parameter.

而准确计算聚束段腔间耦合系数又是设计聚束段耦合孔几何结构的关键.

The micropore structure of argillaceous rock and its correlation with diffusion coefficient

泥质岩微孔结构及其与扩散系数关系

Effects of pore fluid property, contents variety and measurement frequency variety on frequency dispersion of argillaceous sandstone are analyzed.

分析孔隙流体性质及含量变化和测量频率变化对泥质砂岩频散特性的影响。