弯曲的例句大全

However, many pipe bends are still made in this fashion.

然而, 许多管弯曲仍然是这种方式.

In this article, the KNG-k-ε turbulent model is used which can make good result on transient flow and bend flow.

RNG模型相比于标准k-ε模型对瞬变流和流线弯曲的影响能作出更好的反应。

Current KWS provides a flexion-extension movement with one fixed rotation center, which is partially incomparable to biomechanical contours.

本模拟膝关节磨耗机提供一固定旋转中心之弯曲-伸展运动，但部分仍与人体膝关节之生物力学不相合。

Keep left leg bent with heel planted. Put your weight on that leg.

保持左腿弯曲、踮起脚来.把你身体的重量放在左腿上.

Mature bud (4-)6-7 cm. Corolla red, tube slightly curved, inflated, lobes lanceolate, ca. 20 mm, reflexed.

成熟芽（4-）6-7厘米。花冠红色，筒部稍弯曲，膨大，裂片披针形，约20毫米，反折。

Based on numerical and experimental results, for separation channels with a width of 80/ ttn, 31% is the optimal constriction ratio to reduce band broadening by introducing narrowed turns.

综合数值计算和实验结果，对于宽度为80μm的分离微通道，采用收缩弯曲微通道降低样品区带增宽时的最优收缩比为31%。

In this paper, we established a wormlike chain ( WLC) model with variable local persistence length to study polymer molecules with different bending stiffness at each point.

本文针对链上各点处弯曲刚度不同的聚合物分子，建立了变持续长度蠕虫链（WLC）模型。

The tensile strength and the bending modulus of RHDPE/ EVA/ MWRP blend increased by 35% and 25% respectively when the waste rubber powder was modified by self-made surface modifier ACDI.

废胶粉经自制表面改性剂ACDI预处理后，其相应的RHDPE/EVA/MWRP体系的拉伸强度和弯曲模量分别增加35%和25%，而对共混物的其它性能影响不大。

The computation shows that parameters reflecting the tangential stiffness have more significant effects on torsion mode of structure than those on extensional vibration mode and flexural mode.

结果表明，描述结合面切向刚度大小的参数对结构的扭振刚度模态的影响比对纵向振动模态和弯曲模态的影响显著；

The parameters reflecting normal stiffness have more obvious effects on extensional vibration mode than those on flexural mode and torsion mode.

结合面法向刚度大小的参数对纵向振动模态的影响比对弯曲、扭振模态的影响显著；

Branches may be made straight, but not an old tree.

嫩枝易矫直, 老树难弯曲.

The mechanical analysis on axial bending of pump barrel

有杆泵泵筒的纵向弯曲机理分析

Two series of fatigue crack growth rate ( FCGR) tests using three point bend specimen with different integral knife edge designs are performed. Effect of elastic modulus on the measurement of fatigue crack length using compliance technique is analyzed.

用不同整体刀口设计的三点弯曲SE（B）试样做了两组疲劳裂纹扩展速率（FCGR）试验，分析了弹性模量在柔度法测量疲劳裂纹长度中的影响。

Conclusions: Each method a useful tooldifferent measuring scale and different studying purpose.

结论: 不同根管弯曲度测量法的研究侧重点与观察尺度不尽相同,因而其适用范围也是不同的.

Semi-hard magnetic 2 J 4 alloy was fabricated via Equal Channel Angular Pressing ( ECAP ).

开发了用等径弯曲通道变形 ( ECAP ) 制备半硬磁2J4合金.

Is there any bend in the seamount chain?

海山链有弯曲的地方 吗 ?

The effect of shearing on short and thick spindle bending stiffness is discussed.

本文讨论7在计算短、粗主轴弯曲刚度时，剪力时这一刚度的影响，给出了在计算剪切挠度时，剪切变形在空心主轴截面上不均匀分布系数X的近似值；

The dynamic characteristic of transmission's bend vibration and torsion vibration was analyzed in this paper.

本文分析了传动系统的弯曲振动及扭转振动的动态特性.

Analysis of Finite Differential Method for Deflection of Box-like Structure with Reinforced Plates

加筋箱形结构弯曲变形的有限差分法分析

Analysis on Hot Coilbox Bending Roll Control

热卷箱弯曲辊控制浅析