斜的例句大全

Effect of the underlying bedrock slope on seismic ground motion in the Xuzhou area

徐州市埋藏基岩斜坡对地震动的影响

Cobalt benzoate was synthesized by rheological phase reaction. The complex was characterized by elemental analysis and IR.

用流变相反应合成了苯甲酸钴，通过元素分析、红外光谱和X-射线粉末衍射表征了该配合物，系层状结构，属单斜晶系。

Based on the point of tectonic geomorphology, the geomorphology in and outside the Taiyuan Basin were divided into four geomorphologic units: periphery block rising mountain, slightly rising hill tableland, pluvial sedimentation plain, and alluvial sedimentation plain.

应用构造地貌的观点，把太原盆地及其边缘地貌分为：外围断块抬升山地、抬升轻微的丘陵台地、山前堆积的洪积倾斜平原和沉降堆积的冲积平原4种地貌单元。

The Effect of Biaxial Load in the Sheet with an Inclined Crack

斜裂纹板的双向载荷效应

The designing formula of roll shape with full contact complex curve has been obtained according to the principles associated with the conjugate geometrical relation between rolls and the billet in cross roll piercing for tubes.

本文介绍在钢管斜轧穿孔机中，利用轧辊和轧件存在着共轭几何关系的原则，导出全接触的复合曲线辊型的设计公式。

While at the corner there are corner conditions: deflection or reaction also. equivalent binary digit

沿每个边有两个边界条件：挠度或等效剪力，斜度或弯矩应分别等于沿边界的已给值。等价的二进制数字；等效二进位数；等值二进数

When the motion of the flux tube is oblique direction, most passage positions appear irregular FTEs, and the signatures of Bz is bipolar distribution.

当通量管在x方向有正或负速度分量即斜向运动时，大部分部位测到的B x呈不规则变化，B z表现为双极分布。

We present theoretical investigations of the second-and the third-order group delay dispersion caused by a tilted birefringent filter ( TBF) that is composed of a tilted birefringent plate sandwiched between two linear polarizers.

本文研究了由理想线偏振片和单轴双折射晶体波片（光轴平行波片表面）组成的双折射滤光片倾斜放置时的二阶色散和三阶色散特性。

Within the blind angle area of the Amalog Sonoscope leakage flux inspection system, the rotary rolling caused flaws in seamless steel pipes were missed quite often due to low detection sensitivity.

无缝钢管表面的斜轧缺陷，因位于漏磁纵横向检测机组的盲角区域，检测灵敏度低，容易漏检。

Image Blurring Allowance of Digital Intensity Correlation Metering in the Case of Slant Optical Axis

斜光轴数字强度相关计量的像模糊容限

In this paper the idea is extended to the multi-axle bogie frame, the law of load transfer on bogie frame and its calculation and the distribution of the load are given. Measures for reducing the symmetric load ale also described.

本文依据斜对称载荷的计算原理找出了多轴转向架构架上垂向载荷转移的规律以及附加载荷的具体计算方法。

In steel frame structure, high-strength bolted splice connections in beams and braces are often used when the lengths of members are limited by transportation or erection.

在钢框架结构中，由于构件运输或吊装能力的限制，以及节点设计的构造要求，高强螺栓拼接节点常用于梁的拼接和斜撑的拼接。

Results ( 1) Oblique-axial plane: on this plane, the arrangement of all metatarsal bones and the corresponding relation can be clearly displayed, and morphological features also can be observed.

斜轴位平面：在此平面，中足各骨的排列以及相对应的关系能够清晰显示，并且能够观察到关节面的形态特征。

Bank-to-Turn ( BTT ) missiles have arosen increasing attention since its coming into being.

倾斜转弯 ( BTT ) 技术用于导弹控制越来越受到重视.

Construction technology and quality control measures for steel box girder, high-strength bolt, prestressed concrete box girder and inclined cable are briefly introduced.

简要介绍武汉白沙洲大桥主桥上部结构的钢箱梁、高强螺栓、预应力混凝土箱梁、斜拉索的施工工艺和质量控制措施。

The conical grinding method has four grinding parameters, and for three drill point geometric parameters, the lip clearance angle, chisel edge angle and point angle, the flank configuration is not unique.

麻花钻锥面刃磨方法有4个刃磨参数，当给定外缘转点的结构圆周后角、横刃斜角、锋角这3个结构参数时，后刀面的形状并不唯一。

Two workers whilst working on a suspended working platform were injured after platform tilted suddenly.

两名工人在高空吊船工作时,因工作台突然倾斜而受伤.

The correction methods and equations can be used for dynamic and quasi-static calibrations of pres-sure, force and other transducers in transient excited methods of step or ramp function inputs.

这一修正方法及修正公式可广泛应用于凡是用瞬态激励法（阶跃函数输入和斜坡函数输入）对压力传感器、力传感器以及其它各种传感器的动态和准静态标定中。

A special method of Fourier transform for a kind of functions, say, step function, Ramp function and other functions that can be turned into impulse functions by differentiation is described in this paper.

讨论了阶跃函数、斜升函数和经多次微分后能得到一系列冲击函数的特殊函数傅里叶变换的求解方法。

A mould with an oblique guide pin scroll box structure was designed for the core pulling in two directions of a mould with two cavities.

采用能解决一模两腔的两面抽芯问题的斜导柱滑块结构的模具结构，设计出电流线圈架注射模模具。