曲线的例句大全

Magnetic Field Intensity Distribution in the Space Surrounding a Conic Section Carrying Current

载流圆锥曲线空间磁场的分布

Shape blending of curves: research into geometric continuity preserving

保持几何连续性的曲线形状调配

Nelson-Siegel Model Is Applied by Constitution of National Debt Yield Curve

Nelson-Siegel模型在国债收益率曲线构造中的应用

Research on influence of secondary consolidation on compression time curve

次固结沉降对压缩时间曲线的影响研究

The significance and prospect for the application of plastic drain boards to soft-soil foundation in the northeast cold areas are analysed in terms of degree of consolidation and settlement curve.

通过对固结度以及沉降曲线的分析来说明塑料排水板法处理东北寒区软土地基的重要意义和应用前景。

Algorithm of drawing ellipse by conjugate diameter

根据椭圆共轭直径绘制椭圆曲线的算法

According to a sequence of coning angle, the curve of transmission efficiency versus coning angle is given.

通过选取一系列锥角的大小，测出相应的传输效率，作出传输效率曲线；

Problem is the most value conical section the key and difficult point for high school maths problem, is generally and other content combine comprehensive problem.

圆锥曲线最值问题是高中数学中的重点和难点问题，一般是和其他内容联合起来的综合题。

Sector Constructing for Apex and Focus of Conical Section

圆锥曲线顶点与焦点的尺规作图

The Conical Section Under the View of Projection

射影观点下的圆锥曲线

Problems about the Conical Section Chord through a Special Point

关于过特殊点的圆锥曲线弦的问题

Three expressions of conic section and central force problem

圆锥曲线的三种表示和有心力问题

It is found that heat transfer coefficient increases with fin height, while flow resistance varies as concave curve, that is to say, the resistance reaches the lowest value at a middle fin height.

结果表明，随着流道内翅片高度的增大，传热膜系数随之增大，但流阻曲线则呈凹型变化，即在中间高度时流阻达到一最小值。

The dynamic compliance coefficient curves and the torsional angle amplitude of a rigid disc versus the dimensionless frequency are presented.

文末数值算例给出了动力柔度系数和扭转角幅值随无量纲频率的变化曲线，并与单相弹性介质情况进行了对比分析。

Simulation on Load versus Strain Curves of Concentrically Compressed Concrete Filled Circular CFRP-Steel Tubular Stub Columns

圆CFRP-钢管混凝土轴压短柱荷载-应变曲线模拟

Because the workspace's boundary curve is the farthest point the nose of tool can reach, the boundary point can be obtained by computing mechanism's position inverse solution basing on the idea that one of the six legs reaches the largest length.

由于活动空间的边界曲线为刀具刀尖所能达到的最远点，所以根据从六条腿中一条腿达到最大长度时计算机构的位置反解，可求得其边界点。

Single cam linkage mechanism can overcome the shortcomings mentioned above, however the new problem is that the mechanism can not generate the path which has concave curve.

单凸轮连杆组合机构可克服上述缺点，即可以方便地再现预定轨迹并有精确解，但其缺点是难以实现内凹曲线的轨迹复演。

The research result showed that: With the increase of distance from shield tunnel central axis, the initial excess pore water pressure decreased in a concave curve shape.

分析表明：随着离隧道中心的径向距离增加，土体各点的初始超孔隙水压力呈凹曲线衰减。研究了隧道埋深、盾构直径对土体初始超孔隙水压力的影响。

To Classify the Conic Section with Primary Alternation; A branch and bound algorithm for a kind of indefinite quadratic programming

浅谈用初等变换对二次曲线进行分类一类不定二次规划问题的分枝定界法

A Note on A Method of Reducing Equation of Conic Section

《化简圆锥曲线方程的一种方法》的注记