模拟的例句大全

This paper discussed the horizontal forging process of a high strength long bolt through computer simulation, including the forming technology and technology parameters.

本文通过计算机模拟分析了高强度长螺栓平锻过程的变形特点，对其成形工艺和成形特点进行了分析。

Determination of boiling range distribution of light crude oil by simulated

常温进样测定轻质原油馏程的模拟蒸馏方法

Numerical simulations were carried out to investigate the in-furnace combustion parameters at 1000/ 0 BMCR ( boiler maximum continuous rating) load of pre-and post-retrofit cases.

用数值模拟的方法对改造前和改造方案在10000/BMCR负荷下的炉内燃烧参数进行研究。

Numerical simulation of flow around a bluff body near a plane wall

平壁附近钝体绕流的数值模拟

The simulation result predicted a reasonable thickness profile of the final bottle comparing with the experiment. Also, the effect of stretch process and blowing pressure on the thickness profile of bottle was investigated numerically.

通过计算值与实验值的对比，表明模拟能够较好地预测成型瓶子的厚度分布，并研究了拉伸速率、吹胀压力等工艺参数对瓶子厚度分布的影响。

Three-dimensional network simulation on fissures and the stability analysis on random wedge blocks

基于三维裂隙网络模拟的随机楔体稳定分析

Which blocking plate finite element analysis section, the simulation method, concluded that the edge of the blocking plate is the weakest stress.

其中堵板有限元分析小节，采用仿真模拟的方法，最终得出堵板边缘是应力最薄弱的地方。

The simulative experiment results showed that the complex plugs had strong blockage effect.

模拟试验结果表明，组合段塞对岩芯具有很强的封堵能力。

The vortex breakdown results in the low-energy fluid accumulating on the casing wall spreads out remarkably, which has a large blockage effect on incoming flow.

定常数值模拟结果表明，近失速工况下泄漏涡在叶片通道内部发生破碎，涡破碎使得堆积在机匣壁上的低能流体迅速扩散，对来流产生了很大的阻塞效应。

Related production parameters of water blending well above pump are optimized through the research of software simulation.

通过软件模拟研究，优化了泵上掺水井的相关生产参数。

Research of Combustion Simulation on Engine with Diesel/ DME Blending Fuel

二甲醚/柴油混合燃料发动机燃烧模拟研究

The flow and mixing characteristics of mono-sized particles in the double cone blender are analyzed. And the effect of rotational speed of blender and loading mode on mixing is investigated.

分析了双锥型混合器内均一粒径颗粒的流动和混合特性，模拟了混合器旋转速度和装料方式对混合特性的影响；并研究了填充率对非等粒径二元颗粒体系混合效果的影响。

And the "+" type baffle is an optimal selection. ( 2) 3D numerical studies on solid mixing characteristics in the double cone blender.

双锥型混合器内混合特性的三维数值模拟研究。

For the simulation of the wave fields of the East China Sea, analyzed wind data of NCEP and QSCAT/ NCEP blended wind data ( July 1999 later, with higher precision than the former) are used respectively in the calculation as input wind stress.

分别以NCEP再分析风场和QSCAT/NCEP的混合风场（1999年7月之后，比前者的空间精度要高）为输入风场，对东中国海海域的海面海浪场进行模拟。

Numerical Simulation of Blasting between Adjacent Charge Holes in Rock

岩石中相邻炮孔装药爆破的数值模拟

Numerical Simulation and Theory Study of Rock Blasting without Interaction Charge

不耦合装药条件下岩石爆破的理论研究和数值模拟

The analyses of kinematic process of the helium blanketing effect ( HBE) were performed.

通过计算机模拟，对氦屏蔽效应（HBE）进行了运动学过程的分析。

The simulations using the heating bimetal sheet show that the structure is very powerful, which can yield a linear strain between 30%~ 100% at a temperature change of 100 ℃.

通过使用热双金属片进行模拟，实现了在100℃温度变化情况下30%~100%的线性应变。

The Simulation of The Bond Surface in The Process of Bimetal Plate Rolling by R.P.FEM

刚塑性有限元法对双金属轧制结合面的模拟研究

The manufacture craft of stainless clad strip which is belong to bimetal composite plate is carried out in this paper, and the hot-rolled process of stainless clad strip is simulated using the large finite-element software MARC.

本文利用大型有限元软件MARC模拟了不锈钢复合板的热轧过程，并讨论了不锈钢复合板轧制过程最佳相对压下量问题。