温的例句大全

Design of Insulated Riser of Cast Inserted Die Based on Principle of Volume Contraction of Freezing

基于体收缩原则的铸造模具镶块保温冒口设计研究

The sorts and cause of cracks are analyzed from the aspect of contraction crack, temperature cracking and differential settlement cracking and the control measures are put forward on engineering design, materials, construction and maintenance etc.

阐述了混凝土裂缝的种类，从收缩裂缝、温度裂缝、不均匀沉降裂缝等方面论述了裂缝产生的原因，并从工程设计、材料、施工、养护等方面提出了裂缝控制的措施与方法。

This paper introduces the features of the concrete, analyzes the types of concrete cracks, and sums up the causes of and control measures for the concrete cracks from the aspects of contraction crack, temperature crack and hydration heat crack.

介绍了混凝土的特性，分析了混凝土裂缝的种类，分别从收缩裂缝、温度裂缝、水化热裂缝等方面总结了混凝土裂缝产生的原因及其控制措施。

Sensitivity coefficient obtained from calculation can represent how much the internal temperature variation and contraction affects the early crack of concrete structure.

计算得到的敏感系数能够表示结构内部温度变化和收缩这两个因素对于混凝土结构早期开裂的影响程度。

Evaluation of contraction stress due to temperature variation in buildings of mixed structures

混合结构建筑温度收缩应力的近似计算

Analysis of Contraction Stress and Thermal Stress in Arch Culverts

拱涵收缩应力和温度应力分析

Coating and the substrate surface temperature of the coating would have a bad contraction stress, caused by cracking and peeling off the coating.

涂层与基体表面的温度差会使涂层产生收缩应力，引起涂层开裂和剥落。

On this base, the formula used for calculating the side pressure of ring wall, ring tensile and temperature contraction stress is established for engineering design.

在上述基础上提出的环墙侧压力、环拉力和温度收缩应力的计算公式，可供工程设计中采用。

Based on analyzing the loading stress and the temperature stress ( including contraction stress and warping stress), a calculating method of the slab size is set up.

道面板的尺寸是由飞机荷载和温度（包括伸缩应力和翘曲应力）共同作用所决定的。

Thermo Hydraulics Characteristic Around a High-Temperature Particle Dropping in Coolant Liquid

高温颗粒沉降冷液热工水力特性

All the results showed that spoilage bacteria produced a dramatic effect on the quality and shelf life of smoked and cooked sausage.

表明腐败微生物的生长繁殖和致腐是影响低温熏煮香肠产品质量和货架期的主要因素。

HACCP system of smoked and cooked sausage processing was established. The critical control points were choice and receiving of material meat, repair, the second whipping, smoking and cooking, cutting, the second sterilization and checking of final products.

建立了低温熏煮香肠的HACCP体系，其中关键控制点为原料、修整、搅拌、熏煮、剪节、杀菌和成品检验。

With the orthogonal regression analysis method, the influence of concentration of formic acid, cooking temperature, cooking time and pretreatment time on pulp yield and kappa number is studied in this paper.

本文采用二次回归正交组合设计的试验方法，研究了麦草甲酸法制浆工艺中甲酸浓度，蒸煮温度，蒸煮时间和预处理时间对纸浆得率和卡伯值的影响程度。

Results showed that both the varieties and contents of HAAs and the cooking loss of duck breast increasing along with increasing cooking temperature and time.

结果表明，加工鸭肉的烹调损失及杂环胺的含量与种类随着加工温度的升高与时间的延长而增加。

Vapour Pressure and Temperature Self-Regulating System for Cocoon Cooking Machine

煮茧机压力温度自动调节系统

The maximum temperature of the wall decreases with increasing coolant flow.

随着冷却剂流量的增大，推力室壁中的最高温度明显下降；

The simulation results show that the speed, the temperature and the viscosity of coolant fluid exert much influence on convection heat transfer;

结果表明，冷却液喷射速度和温度以及冷却液的粘度变化对对流换热特性有着明显的影响；

It is usually difficulty to obtain film coefficients between the working roll and the coolant fluid as we solve the temperature field of the roll.

工作辊与冷却液之间对流换热系数的确定是轧辊温度场分析的难点。

The Effect of Water Coolant and Lubricating-oil Temperature on Diesel Engine Fuel Economy

冷却水与润滑油温度对柴油机燃油经济性的影响

An Experimental Investigation of Drag Characteristic of A Hot Particle Moving in Coolant Liquid

高温小球在冷却剂中运动阻力特性的研究