焊接的例句大全

Research on Welding Technology for Anodizing Shaped Aluminium Alloy Material

表面阳极化铝型材焊接工艺研究

Besides, key construction technologies are introduced in detail, such as machinery selection, tower installation, measurement, welding and antenna mast installation.

详细阐述机械选型、塔楼安装、测量技术、焊接技术和天线桅杆安装的施工工艺和关键技术。

Based on the arc light spectrum theory, the auxiliary lighting source and composite filtering techniques were used to solve the negative factors such as poor resolution and radiation disturbance by weld pool.

依据弧光光谱理论，采用辅助光源及复合滤光技术，有效地解决了焊接区熔池成像的干扰和清晰度差等问题。

According to the arc light features of pulsed TIG welding and its effects on vision measurements, a special method of image capturing and controlling is put forward.

根据脉冲TIG焊接电弧的弧光特性及其对视觉检测的影响，提出了一种独特的图象采集和控制方法。

In order to investigate the mechanism of arc light sensing for welding behavior accurately, systematic spectral analysis of GMA and GTA was made.

使用自行建立的计算机化光谱分析系统，对实际焊接条件下的电弧进行了整体和局部的分析。

However, it is very difficult to view the metal transfer process directly during welding, for the strong interference from the arc light.

但是在强烈的焊接弧光下，很难观察的熔滴过渡的过程。

Arc voltage and welding current are signal source.

以电弧电压和焊接电流为采集的信号源。

The progress of the backing weld technology for stainless steel tubes is reviewed.

综述了不锈钢管打底焊接技术的进展,指出了各种方法的特点及应用场合.

The influence of weld heating on microstructure of heat affected zone was investigated in this paper.

探讨了焊接加热对热影响区组织的影响.

Weld hardness is controlled ( including the heat-affected zone ) and maintained below 200 HB.

焊接硬度控制在 ( 包括热影响区域 ) 200HB以下.

Results showed that hardness is a little different in the heat affected zone ( HAZ ).

结果表明,焊接热影响区具有较小的 硬度 差异.

Enclosure is made of casting alloy, surface is plastics and possessing static electricity resisting, shock-proof etc.

外壳采用铸铝合金或钢板焊接而成, 表面喷塑,外型美观,具有体积小 、 抗静电、耐冲击等优良性能.

Participate in robot welding parameter adjustment process.

参与自动焊接工艺的设定和调整.

The article describes the configuration and concept of thyristor speed adjustment system in electro-slag welding machines.

介绍电渣焊接机采用的可控硅调速系统的构成、工作原理.

Welding voltage power grid voltage fluctuations and changes in arc length self-adjusting ability.

焊接电压在电网电压波动及电弧长度变化时自调节能力强.

The process of Cu-Al pipe butt welding was analyzed , which is divided into 6 steps.

分析了铜铝管焊接工艺过程, 并将其分解为6个动作.

The prosperous post buckling load capacity of web plates of box girders can be used.

焊接箱形梁腹板存在较高的屈曲后强度,可供利用.

This machine is ideal for grinding various types of turning tool.

该机能用于磨削各种规格的焊接式刀具.

The article discusses the calculation of mechanical properties of welded metal-bellows applied in mechanical seal devices.

本文主要讨论应用于机械密封装置中的焊接金属波纹管力学性能的计算.

Due to the unique advantage, the electronic beam welding are used extensively.

电子束焊接因其独特的优点, 应用广泛.