熔的例句大全

Dehydration-melting experiment of the biotite-gneiss, eastern hebei, at 1 GPa pressure

冀东黑云母片麻岩在1GPa压力下脱水熔融实验

Melting Experiment of Biotite Gneiss-H_2O System at 0.1-0.2 GPa Pressures

黑云母片麻岩H2O系统在0.10.2GPa压力下的熔融实验

The utility model realizes zipper cutting through the fusing of zipper material, and cutting fluffiness of knife tool and puffed selvedge phenomenon can not happen, and simultaneously noise is small.

它通过拉链材料的熔断实现拉链的切断，不会产生刀具切断的起毛、散边现象，同时噪音也很小。

Performance of External Fuse Protection and Connection Mode of Capacitor Group

外熔丝保护性能与电容器组接线方式

The temperature field distribution of raceway play an important role in continuous and steadily production through evenly descend of the upper charging of the blast furnace, the drippage of melted slag and iron, the gas distribution.

回旋区温度场分布，影响高炉上部炉料的均衡下降、熔融渣铁的滴落和炉缸的煤气分布，对保证高炉整个冶炼过程连续、稳定地顺利进行起着至关重要的作用。

The major, trace element and isotope geochemical characteristics of the basic lavas of the Kule Lake ophiolite indicate that the basic lavas have a N-MORB affinity, possibly suggesting a small ocean basin environment for them.

本文通过对蛇绿岩基性熔岩的主量、微量和同位素地球化学研究，结果表明库勒湖蛇绿岩具N-MORB特征，推测其形成于小洋盆环境。

Effects of the Amount of Solvent Minerals and Alumina Ratio on Cement Raw Material Burnability

熔剂性矿物的数量和铝率对生料易烧性的影响

Ultrasonic tandem method is usually adopted to detect the weld seam of a high pressure container in which dangerous flaws exist, such as boundary unblended and crack.

高压容器的焊缝常存在边界未熔合、未焊透、裂纹等问题，一般利用超声波串列扫查方法对焊缝进行无损检测。

And Al_2O_3 is the essential condition of the creation of needle-shaped calcium ferrite.

软熔性能，Al2O3是针状铁酸钙生成的必要条件。

The lavas mainly include basalt, dolerite, fumarolic, amygdaloidal andesite, trachy-andesite and as well as rhyolite.

火山熔岩类主要包括玄武岩、粗面玄武岩、气孔杏仁状安山岩、粗面安山岩、流纹岩等。

LTTE weld toes dressing technology to improve fatigue behavior of welded joints

提高焊接接头疲劳性能的低相变点焊条焊趾熔修技术

Influence of Additive in IMX on Density of Eutectic Explosive Pellet

IMX中添加剂组分对熔铸药柱密度影响的研究

The design of location and size of over flow well, and reasons which resulting in the defects such as flow mark near the gate, melt burned and gas leaking from the gas entrance are analyzed, and the solving measures are put forward.

对溢料井的位置和尺寸的设计，以及浇口处流痕、熔料烧焦和气嘴漏气等成型缺陷产生的原因作了分析，并提出了解决措施。

Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times.

加工窗口分析、它零件的模流分析，检查熔体温度、具温度、塑压力和充填时间。

Study on Effects of Heat Transfer Coefficient between Polymer and Mold on Melt Filling Flow in Micro Injection Molding

微注塑成型中熔体与壁面间传热系数对充模流动影响的研究

Second, numerical simulation of filling, flow, air pocket, fusion trace, and warp were performed with simulation software Mold flow.

其次，利用仿真软件Mold flow对该注塑件进行充填、流动、冷却、气穴、熔接痕、翘曲等数值模拟。

Then the basic process to use Mold flow software to realize the numral simulation of the fusion polymer filling the mould cavity is introduced.

然后重点说明了用Mold flow软件，通过有限元的方法实现熔融聚合物流体充填模具型腔时数值模拟的基本过程。

The Development of High Voltage HRC Fuse

限流式高压熔断器的发展

In this paper the author mainly introduces the present situation and future development of high-voltage HRC fuse.

本文主要介绍限流式高压熔断器的现状和今后发展的方向。

The study of the nanostructured refractory metals was mentioned.

简述了纳米晶难熔金属的研究现状.