误差的例句大全

The test results show that the basic error, linearity of the capacitive angular sensor can be more effectively improved than before. The average of the former decreases from 2% to 0.2%, and the later from 0.58% to 0.22%.

测试结果表明，利用本系统校准，电容转角传感器的基本误差、线性度指标都得到有效改善，前者平均值从2%降低至0.2%，后者由0.58%降至0.22%；

Rough rolling and pure rolling temperature drop model is derived by regression statistics way with the measured data, can see this model has good prediction, forecast and actual temperature temperature ± 15% than basic error.

粗轧和精轧的温降模型通过回归统计的方式导出，与现场的实测数据比较，可以看出该模型具有很好的预测度，预测温度与实际温度的误差基本不超过±15%。

Using Power-comparison to Measure the Basic Error of Energy Meter

采用功率比较法测量电能表基本误差

The test of immobilized enzyme activity shows that the immobilized enzyme's reusable ability is good enough to be applied in the future industry production despite of experimental error.

将固定化好的酶进行测试发现，排除掉实验误差后该固定化酶的可反复使用性良好，可以应用于未来的工业生产中。

Setting Method of Baud Rate of CAN Bus and Its Error Analysis

CAN总线波特率设置方法及误差分析

The study shows that this approximate solution will yield relatively great errors in many cases.

研究表明,很多情况下这种近似解法将产生较大的误差.

So it is necessary to calculate gravity anomaly real-time on the missile.

主动段扰动引力是引起弹道导弹制导方法误差的主要因素.

In particular, Section 2.3 discussed a number of error sources that can seriously affect measurement accuracy.

特别是, 在第2.3节讨论了各种严重影响测量准确度的误差源.

A mathematical model on the influence of three-dimensional locating upon machining accuracy is established.

建立了三维定位误差影响加工精度的数学模型.

Error compensation is an efficient way to improve machining accuracy of NC machine tools.

误差补偿技术是提高数控机床加工精度的有效途径.

The possible errors, like overcounting or double-stepping, were overcome using design interventions.

可能存在的诸如过度计算或重复计算脚步的误差，也通过干预措施被消除了。

Comparative Analysis of Dentiform Error by Scatter Measuring and Seriate Measuring

离散与连续测量齿形误差的分析比较

Analytic calculation of ellipticity error effect in neutron penumbral imaging

中子半影成像中椭圆度误差的解析计算

There is more error in simulating void growth under unaxisymmetry triaxial stress conditions using R-T model and GTN model.

用R-T模型、GTN模型模拟非轴对称三轴应力状态下材料微孔洞损伤演化有较大的误差。

The errors of replication in GIR and GRd were 1.4% and 1.9% respectively.

重复试验GIR和GRd误差范围为1.4%和1.9%。

An analysis on the geometrical firing data ( gfd) error of self-propelled guns positioned by GPS

自行火炮GPS定位几何诸元误差分析

Based on the relative error minimizes principle, the grey combination prediction model was discussed.

以这些模型为基础,按照相对误差极小化的原则, 建立了灰色组合预测模型.

OEM clients who signs this order confirmation means acceptance of ±5 % manufactuirng error.

凡订做产品者,签订此函即表示接受±5%的生产数量误差.

An error compensation method for intelligent electromagnetic compass ( IEMC ) is studied.

研究了一种智能电子罗盘的误差 补偿问题 .

Present a error compensation algorithm, the error is caused by the phase.

本文提出了对这种相位引起误差的一种补偿算法.