转速的例句大全

Design Calibration and Application of Pulsating TACH

脉冲式转速表的设计、校验与应用

Optimize on Working Parameters Crank Rolling Velocity and Radius of the Vibration Sieve about Cereal Cleaning Windmill

谷物清选风车中振动筛的曲柄转速和半径优选

The main cause for such failure was the high varying stress from the blade flutter because of its relatively small flutter margins.

叶片颤振裕度不大，在工作转速范围内产生颤振导致叶片承受较大的动应力是其疲劳断裂的主要原因。

Numerical off-line simulation is carried out at different starting up conditions ( engine engaging speed, load torque and clutch LQR control parameters). The results are investigated and analyzed.

在不同的起步条件下（发动机起步转速、负载以及离合器LQR控制参数）对该模型进行了离线仿真分析，并与闭环控制策略的起步性能进行比较。

The three-dimension finite element precise model of helical gears is established and impacting calculation is made in this model, the von mise stress, contact pressure and distortion are compared with in different engaging speed and time.

建立了斜齿轮三维有限元精确模型，并进行了冲击有限元计算，综合比较了在不同接合转速、不同接合时间工况下，斜齿轮各部位的应力、接触压力和变形状况；

The settle time is related to the angle of harrow leaf and harrow blade and principal axis speed of drier.

物料在小干燥盘上的停留时间与耙叶和耙刃的角度以及干燥机主轴的转速有关。

Tests show that the test-bed is stable operation, can meet the intended function. A life simulation test is done in a vacuum test chamber for a different load and speed, test environment selected high and low temperature and room temperature in vacuum.

试验证明该实验台运行稳定，能满足预定功能。在真空高低温试验箱内进行了不同载荷和转速下轴承寿命模拟试验，试验环境选择了真空常温和真空高低温。

Cargo and ballast pump speed control system

货油及压载泵转速控制系统

If the blade is long and rotate speed of breaking is high, there are two notches in which the second notch is deepest and the blade bend into the shape of "U".

对于较高转速下飞断的长叶片，机匣上形成的第二个凹坑最深，叶片也卷曲厉害；

The flow and mixing characteristics of mono-sized particles in the double cone blender are analyzed. And the effect of rotational speed of blender and loading mode on mixing is investigated.

分析了双锥型混合器内均一粒径颗粒的流动和混合特性，模拟了混合器旋转速度和装料方式对混合特性的影响；并研究了填充率对非等粒径二元颗粒体系混合效果的影响。

The effects of screw barrel temperature and screw block structure on the extrusion technology, as well as the connection between screw speed and inherent viscosity of PEI were discussed.

讨论了螺杆筒体温度、螺块结构对反应挤出工艺的影响及螺杆转速与PEI特性粘度的关系；

The structural design for foundation of frame style axial blower under circumstances of high rotation speed and high intensity is mainly discussed in the paper.

文章主要论述框架式鼓风机基础在高转速、高烈度情况下的结构设计。

I mainly produce braking unit, braking resistor, torque motor controller, inverter panel extension cables, tachometer, counters.

我部主要生产制动单元、制动电阻、力矩电机控制器、变频器面板延长电缆、转速表、计数器。

Hardware and Software Design on Automate Control for The Rotational Speed of Metering-Device's Axle

排种器转速自动检测的硬件及软件设计

The Design of Tach/ Hourmeter with Stepper Motor

步进电机式转速小时表设计

After increasing the impedance, the big machine volute inlet pressure, the greatest rotational speed rises, the surge tank highest swell surpass the design value, which does not favor the big machine security steady operation.

在增大阻抗后，大机的蜗壳进口压力、最大转速上升、调压井最高涌浪都超过设计值，不利于大机的安全稳定运行。

The results show that: the response time of optimized electromagnetic value which control diesel dump truck speed out of control more effectively is earlier 5.59 ms than before, the optimized system improves obviously the safe operation of diesel dump truck and service life.

结果表明：断油电磁阀参数优化后的喷油系统比优化前的系统的响应时间减小了5.59ms，能更有效地控制柴油机自卸车转速失控，明显提高柴油自卸车的运行安全和使用寿命。

Rotating speed is lower than the set value.

转速低于规定值.

A 15% SiC_p/ 2009Al composite was fabricated by high energy milling powder metallurgy ( PM) technique. The effect of velocity and time of milling as well as PM procedure on mechanical properties of the composite was investigated.

采用高能球磨粉末冶金法制备了15%SiC p/2009Al复合材料，研究了球磨转速、球磨时间、加热抽真空工艺、热压成型以及热挤压比对复合材料力学性能的影响。

But one but the rotational speed falls, also will be unable to start!

但是一但转速掉下来的时候, 也会死火!