Be sure to ask the doctor or pharmacist if any of your medicines cause dry mouth.

Dry mouth can often Ophiopogon japonicus, such as Chinese medicine Shashen tea drinking.

口腔干燥可经常用麦冬, 沙参等中药泡茶饮用.

The common adverse reactions of this drug are dry mouth, headache, nausea and insomnia etc.

常见不良反应为口干 、 头痛 、 恶心、失眠等.

Occasionally, ice chips may be ordered because they relieve a dry mouth.

有时可在护嘱中使用冰棒,他们可以起到缓解口干的作用.

In indicated that the quantitative grading method was more objective than the current qualitative one in reflecting the real endangered situation of the 32 medicinal plants.

通过对32种药用植物的综合评价表明，本定量分级比目前国内外采用的定性分级，能更客观地反映出药用植物的受威胁状态和需要急切保护的程度。

GOLD criterion is more suitable for the diagnoses and classification of COPD than that of national existent criterion;

GOLD诊断分级标准比我国现行的诊断标准更适合我国的COPD诊断分级；

The result is basically the same among comprehensive score, grading graduation constitution ratio, result of present situation analysis in the cities.

从各设区市综合评分、评分分级构成比以及现状分析结果来看，结果基本一致。

There were significant differences in the constituent ratio of eyeground arteriosclerosis grade among normal control groups cerebral infarction with High lipids group and cerebral infarction without High lipids group.

脑梗塞高血脂组、脑梗塞非高血脂组和对照组眼底动脉硬化分级构成比不同。

Pain score and classification were decreased significantly ( P < 0.01).

术后疼痛评分和痛经分级比术前明显降低（P<001）；

Wood sugar alcohols, plasticizers, resins and so on.

木醇糖 、 增塑剂 、 树脂等.

The independent principle, envelope principle and maximum material principle were given in National Standard of Geometrical Tolerances and Tolerances principles. These three principles show the relation between size tolerance and Geometrical tolerances in drawings.

《形位公差》和《公差原则》国家标准对图样上给出的尺寸公差与形位公差的关系规定了独立原则、包容原则和最大实体原则。

An Investigation of Dimensional Tolerance of Castings in Several Investment Casting Factories Study of Conformance Test for Size Tolerance

若干熔模铸造工厂铸件尺寸公差实况调查分析

The Influence of Size Tolerance and Reflectivity of the Surface on the Characteristics of Compound Parabolic Concentrators

尺寸误差及表面反射率对复合抛物面聚光器特性的影响

Technical factor of influencing size tolerance of cold stamping for sheeting material was analyzed and economic tolerance of cold stamping was mentioned.

分析了影响板料冷冲压件尺寸误差的工艺因素，提出了冷冲压件的尺寸经济精度。

With the change of scanning speed, the size tolerance of the PP part exhibited a minimum.

随着扫描速度的变化，试件翘曲量存在极小值。试件的尺寸误差随着激光功率增大、扫描速度降低或铺粉厚度减小而降低。

This paper discusses the method of defining size tolerance in the working procedure, makes use of craft technique to define tolerance and raises the simplified calculation of craft technique.

论述工序尺寸公差的确定方法及利用工艺能力确定工序尺寸公差，给出工艺能力的简化计算方法。

Other special size tolerance may be satisfied on request.

特殊尺寸公差可由买卖双方协议。

The sizing process must be taken in order to eliminate the size tolerance and roundness one after the seamless pipe rolled and heat treated.

为消除无缝钢管的轧制和热处理所产生的尺寸和椭圆度误差等缺陷，一般要采用定径工艺。

We calculate and analyze the mutual compensation between size tolerance and form& position tolerance while applying the minimun material requirement to the tested essential factors and standard key elements.

对被测要素、基准要素在应用最小实体要求时，尺寸公差与形位公差相互补偿问题进行计算分析。

During the intermediate annealing, foil material rolling, the effective action has been taken to guarantee the size tolerance;

在中间热处理、箔材轧制等环节采取有效措施保证了尺寸公差；

In the third chapter, mathematical model of size tolerance, form tolerance, orientation tolerance and location tolerance of cylindrical feature was established.

第三章：建立圆柱要素尺寸公差、形状公差、定向公差和定位公差的数学模型。