The rabbet water yield includes two parts of underground water and surface water.

The utility model relates to a fishplate connector, which comprises a substantially cylindrical shaft which is inserted into a rabbet ( 1) and holes of arm plates ( 2 and3) on a support frame.

鱼尾板连接装置包括基本上呈圆柱形的轴，该轴插入榫头（1）和支架上的臂板（2和3）的孔中。

Based on FEA and standard fatigue sample test, using the FEA method, deeply analyzed the disk mortises' contact stress with blade rabbets.

以有限元分析和标准试件疲劳试验为基础，通过有限元分析的方法，细致分析了轮盘处于工作状态时，叶片榫头的接触应力对榫槽底部应力状态的影响。

Of highway bridges, prefabricated cellular slab bridges are employed in great numbers, of which the bridge floor paving is generally subjected to early structural failures mainly characteristic of longitudinal cracking along the rabbets of the cellular slabs.

公路桥梁中大量采用的装配式空心板桥，其桥面铺装普遍存在以沿空心板企口缝纵向开裂为主要特征的早期结构病害。

Through modeling experiment, this method is proved to be feasible for analyzing the rabbet assembly structure.

通过模态实验校验的手段证明用这种方法进行榫接装配系统动力学分析是可行的。

A joint formed by fitting together two rabbeted boards.

通过联合两块嵌接的木板形成的接合处。

The device is three groups of groove chambers composed of three deckle boards whose clearances are clamped with two dialysers and both sides of which are accompanied by electrode rabbets.

本装置是由三块框板间隔夹着两张透析膜，两侧附有电极半槽构成的三组槽室。

The article introduces the checking templates in manufacturing the bus body, especially in the design and manufacture of the checking templates that are used in back wall transverse radian, windscreen and windshield rabbet

介绍客车车身制造过程中的检验样板，尤其是后围横向弧度、风窗玻璃和风窗止口的检验样板的设计和制作方法

Objective To explore the protective effects of atrial natriuretic peptide ( ANP) on alveolar type II cells ( AT-ⅱ) in rabbets with acute respiratory distress syndrome ( ARDS) induced by endotoxin ( ET).

目的：研究心房钠尿肽（ANP）对急性呼吸窘迫综合征中肺泡Ⅱ型上皮细胞（AT-Ⅱ）的保护作用。

The front end cover and the rear end cover are fixed by screws and rabbets. Meanwhile, the rotor assembly is fixed.

前、后端盖利用螺钉及止口固定，同时将转子总成固定。

Leak analysis of HP carbomate preheater and tenon jointing seal construction

甲铵预热器的泄漏原因与榫槽密封结构

First, the theory of fretting wear and studies on fretting fatigue were introduced and the parametric method was used in the process of creating the model of dovetail joints in UG software.

本文介绍了微动损伤的机理和微动疲劳寿命的研究方法；利用UG软件对燕尾榫联接结构创建了参数化实体模型；

Fretting fatigue in component& the feature in circumferential dovetail joints

构件微动磨损疲劳&盘上周向燕尾榫槽的特点分析

Study on Numerical Control Mill-tenon Machine for European Fashion Wood Windows

欧式木窗数控铣榫机设计理论

This paper focuses on the design method of firtree tenon/ mortise, the three-tooth firtree joint model is established with parametric method by UG software.

本文通过UG软件对涡轮榫头/榫槽三齿结构进行了参数化建模；

Crack Analysis on Rabbet of Grade ⅰ Turbine Disk of an Engine

某型发动机Ⅰ级涡轮盘榫齿裂纹分析

Thermal elastic-plastic analysis and computer flowchart for turbine blade root fastenings

透平叶根接触榫槽的热弹塑性分析和计算流程

VC++ program design of parametric graph for dovetail joint

基于VC++的燕尾形榫参数化程序设计

JSF Round-hole Pearlite Partition Plank

圆榫及孔公差探讨JSF珍珠岩圆孔隔墙板

Mortise 2 D Stress Intensity Factor Determination by Laser Speckle Method

激光散斑法测定榫槽二维应力强度因子

Flat countersunk double nib bolts Remove hinge retaining nuts from studs.

GB/T800-1988沉头双榫螺栓从双头螺栓拆下固定铰链的螺帽。